Will a motorized screen stop if it hits someone?
Often, but you cannot count on it. Many screen motors stop, and some back up, when the bottom bar meets resistance. But the makers built that feature to protect the screen, not people. Becker says its zip motor's detection may not be used to protect people. Somfy lets the down-stroke detection on its Maestria 50 RTS be switched off from the remote. Rollease Acmeda's Automate FT motor does not look at all in the last 20 cm (about 8 in) above the floor. So treat a moving screen like a garage door with no safety eye: keep people and pets out from under it while it runs.
Key takeaways
- Obstacle detection means the motor senses that turning the tube suddenly takes more force than it should, and stops. It measures the motor's effort, not what is under the bar.
- Becker: "designed exclusively" to protect the screen, and not allowed as protection for people. Elero: stops "to protect the cloth." Somfy io: to "protect the driven product."
- Somfy Maestria 50 RTS down-stroke detection can be switched off or made more sensitive. Its up-stroke detection cannot be switched off.
- Rollease Acmeda Automate FT: no detection in the first 20 cm below the top limit or the last 20 cm above the bottom limit. A paw on the sill is in that zone.
- A sun sensor or timer lowers the screen when nobody is watching. Switch automation off while the patio is in use by children or pets.
What is obstacle detection on a screen motor?
A motorized screen is driven by a tubular motor, a motor hidden inside the tube the fabric winds onto. Obstacle detection is a function in that motor's electronics. It watches how hard the motor has to work to turn the tube. When the effort jumps past a set level, the motor treats it as something in the way and stops. Some motors then back up a little.
Somfy's troubleshooting sheet says it plainly: a more sensitive setting "will then require less torque to detect an obstacle." Torque is the turning force on the tube. Elero lists the same idea as "smart force measurement." So the motor does not see a child, a dog or a chair. It feels a rise in effort. A sticky channel, ice or a heavy bar can cause the same rise. A soft object that gives way may cause too little. How the motor, brake and limit unit sit in the tube is shown in tubular motor internals.
A limit is a different thing: the set stop at the top or bottom of travel, covered in resetting motorized screen limits.
What five screen motors actually do
| Motor | Going down | Going up | Can it be changed? | Where it does not look | What the maker says it is for |
|---|---|---|---|---|---|
| Somfy Maestria 50 RTS | On at a default level; stops the screen | On; "can not be deactivated" | Down only: off, or more sensitive, from the remote | No zone given | No purpose stated; the troubleshooting sheet tells installers to turn it off if it blocks limit setting |
| Somfy Maestria+ 50 io | Stops, then raises slightly | Stops | No setting in the instructions | Works "only with compatible driven products" | "protect the driven product and remove any obstacles" |
| Becker S18 (zip screens with a heavy bar) | Stops, tries again, off after the third attempt; within about one tube turn of the bottom, stops at the first hit | Same rule; 10 attempts per run | No setting in the manual | Not active without Becker's detection drive adapter | "Exclusively" to protect the screen; not as protection for people |
| Elero SunTop/Z M RH | "Blind protection down": stops quickly | "Blockage detection up" | Not stated on the product page | Not stated | "to protect the cloth" |
| Rollease Acmeda Automate FT (Zipscreen) | Impact detection: the motor retracts the screen | Not stated in the manual | Can be switched off at installation | First 20 cm below the top limit, last 20 cm above the bottom limit | Not stated in the manual |
Somfy Maestria 50 RTS
Somfy's Maestria 50 RTS quick programming guide (October 2018) says the setting lets you "deactivate the obstacle detection or increase the sensitivity up from the default level during the downward movement." The steps start with the screen halfway. Press MY and UP briefly, then press them again until the screen jogs. Two short UP presses switch detection off. Two short DOWN presses make it more sensitive. Hold MY to save. A short jog instead of a long one means you are back at the default. Neither Somfy guide names a zone where detection is off.
The Maestria RTS helpful tips sheet (September 2018) adds two facts. First, "the upward movement obstacle detection can not be deactivated." Second, it suggests more sensitivity for a "narrow product featuring a lighter load bar" or a motor with "excessive torque compared to the end-product's size."
The same sheet shows why you cannot assume detection is on. When the motor will not go down during setup because detection keeps tripping, Somfy's fixes include helping the bar down by hand. Then: "Once the limits are set, deactivate the obstacle detection." A screen set up that way runs down with no detection at all, and nothing on it tells you so.
Somfy Maestria+ 50 io
Somfy's Maestria+ 50 io instructions (2015) describe detection in both directions. Going down, the screen "stops automatically and raises slightly so the obstacle can be removed." Going up, it "stops automatically." The manual says detection "can be used to protect the driven product." It also says it is "operational only with compatible driven products," and tells you to ask an installer which those are. The instructions give no way to change or switch off detection.
Becker S18
Becker's S18 installation manual (4 July 2025, German) covers zip screens with a heavy bottom bar. These figures were first used on this site in zip screens in winter. Our translation: when the motor senses an obstacle or a fault in the fabric, it stops and tries a second time to get past. If that fails, it switches off after the third attempt. About 360° before the lower limit, it stops at the first detection and does not retry. A run toward either end is capped at 10 attempts in total.
One turn of the tube is a short distance. Our calculation: a near-empty 50 mm tube moves the bar about π x 50 = 157 mm per turn (about 6 in). A 78 mm tube moves it about 245 mm (about 9-1/2 in). Detection is also only active with Becker's "drive adapter for obstacle detection" fitted, and with the motor pushed fully into the tube. Then the warning: using the detection "as protection for people is not permitted. It was designed exclusively" to protect the sun protection system from damage. The manual gives no setting to change detection.
Elero SunTop/Z M RH
Elero's SunTop/Z M RH page sells a hardwired motor for zip screens with "Blind protection down" and "Blockage detection up." It says the down function "stops quickly when it encounters an obstacle in order to protect the cloth." The page gives no setting and no blind zone. This motor also appears in battery vs hardwired screen motors.
Rollease Acmeda Automate FT
Rollease Acmeda's Zipscreen installation manual (v4.4, March 2020) covers the Automate FT motor. Its troubleshooting table says impact detection "isn't active in the first 20cm from the upper limit and in the last 20cm from the lower limit." The same row gives a second cause: detection "has been deactivated during motor installation." The fix is to press P2, DOWN and DOWN on the remote, then test that the motor "retracts the blind when an obstacle is detected." The blind zone sits at both ends of travel, not only the top. The manual says nothing about detection on the way up, or what the feature is for.
Worked case: a chair under a screen on a timer
Take a 10 ft zip screen on a patio, set to lower at 3 pm. Suppose someone has pushed a dining chair back so its top rail sits under the bar's path. Nobody is outside. Here is what each motor's document says should happen, walked through the figures above.
Why does a screen stop or back up with nothing there?
Because detection reads effort, anything that adds drag looks like an obstacle. The makers' documents name these causes:
- The bar rubs in the channel. Rollease Acmeda traces a screen that "gets jammed half way down" to the bar end cap hitting the inner rail. Its fix is to match the installed width to the measured width, or trim the bar. It also wants the inner rail parallel with the zip "to avoid strain or jamming." Alignment is in installing motorized patio screens.
- Wind. The same manual says wind pushes the fabric against the inner rail and "stops blind momentarily." When the wind drops, the blind drops.
- Undersized motor. Somfy's first fix when detection blocks the downward run is a higher torque motor: "The torque in the motor used is undersized." Its second is to help the bar down by hand to absorb "the potential bounces made by the load bar."
- Ice. The Maestria+ 50 io has a frost protection that "functions in a similar way to obstacle detection": if the screen "detects any resistance, it stops automatically." A frozen screen should not be run at all; see zip screens in winter.
- The bar touches the cassette. Somfy's sheet lists a screen that reaches the top limit and then the bar goes down again. Its fix is to reset the top limit about 1/4 in lower, because "The load bar shouldn't touch the cassette."
Fix the drag before you change the setting. A motor made less fussy by switching detection off still has a bar rubbing in its channel, and it has lost the one thing that stopped it. Other faults, like a dead motor or one remote that does nothing, are in retractable screen repair.
Sun sensors and timers: the screen moves when nobody is watching
A hand on the remote means someone is looking at the bar. A sun sensor, a timer or a hub scene removes that person. Becker's safety notes assume someone is there (our translation): do not run the system "if persons or objects are in the danger area," and "watch the danger area during operation." Becker also asks for at least 40 cm (about 16 in) between moving parts and nearby objects.
Somfy's guide warns about automation set up wrong. If the remote's direction is set wrong, an Eolis or Soliris RTS sensor "will not function in the manner it was intended. Damage to the screens and injury may occur as a result." How sun and wind sensors decide when to move is covered in sun and wind sensors. The same rules apply to screen motors.
Our advice for automated screens follows from the documents above:
- Keep the strip under the bar clear: no chairs, dog beds or planters in the path.
- Turn the sun sensor or timer off while children or pets use the patio. Turn it back on when they go in.
- Ask your installer which motor you have and whether detection was left on. On a Maestria 50 RTS, Somfy's own tip may have switched it off.
- Test it the way Rollease Acmeda suggests, away from both limits. Lower the screen onto an empty cardboard box taller than 8 in, and check that the motor stops or backs up.
What to do with children and pets around
Becker allows children 8 and older to use the drive only when supervised or taught how to use it safely, and says "Children must not play with the device" (our translation). So keep remotes and wall switches out of reach of small children. Do not let children ride, hang on or hide behind a moving screen. A screen is also not a pet gate: a lowered screen can be lifted by a motor or a sensor at any moment. Other safety points for patio screens, including bar weight and where the bottom limit belongs, are in motorized patio screens.
Choosing a new motor for a home with small children or pets? Ask for detection in both directions, the blind zone in writing, and detection left on at installation. That will not make the screen a safety device, but the motor will try to stop in more places.
What this answer does not cover
We read the documents of five motors. Your screen may use another motor, an older version, or a control system that changes how the motor behaves. None of the documents gives a force in pounds or newtons at which detection trips. So no one can say from paper whether a given motor would stop on a child's arm before it hurt. No maker we read claims that it would, and Becker says outright that it may not be used for that. We did not read any safety standard for powered screens, so this page does not say what a standard requires. Battery and solar motors have their own manuals. Anything about an injury, a recall or a motor that will not stop is a question for the maker or your installer, not for a setting on the remote.
Bottom line
Most screen motors stop when the bar hits something firm, and some back up. That is screen protection, not a safety system. It can be switched off, it may not look near the floor, and it reacts to drag, not to bodies. Keep people and pets clear while a screen moves, and switch automation off while they are outside.
Sources
- Somfy, Quick programming guide for Maestria 50 RTS motors, October 2018: obstacle detection setting, sensor direction warning.
- Somfy, Maestria RTS helpful tips (P-0033), September 2018: up-stroke detection cannot be switched off, undersized torque, switching off after limits, bar touching the cassette.
- Somfy, Maestria+ 50 io instructions, 2015: obstacle detection and frost protection.
- Becker-Antriebe, S18 tubular drive installation and operating manual (German), 4 July 2025: obstacle detection, safety notes.
- Elero, SunTop/Z M RH product page. Read 2026-11-16.
- Rollease Acmeda, Zipscreen installation manual, v4.4, March 2020: Automate FT impact detection, troubleshooting table.
Frequently asked questions
Do motorized screens have a safety sensor like a garage door?
Not in the documents we read. A garage door opener's photo eye looks across the opening. Screen motors only feel a rise in the effort to turn the tube. Becker says its detection may not be used to protect people.
Can I turn obstacle detection off?
On a Somfy Maestria 50 RTS, yes, for the down stroke, from the remote. The up stroke cannot be switched off. On a Rollease Acmeda Automate FT, it can be switched off at installation. Turning it off to stop false trips hides the drag that causes them.
Why does my screen go back up a few inches by itself?
Some motors raise the bar slightly after detecting resistance, like the Maestria+ 50 io. With nothing there, look for the bar rubbing in a channel, wind pressing the fabric into the rail, ice, or a motor too weak for the screen.
Will the screen crush something on the floor?
It can press on it. The Automate FT does not detect in the last 20 cm above its bottom limit, and Becker's motor stops at the first hit without retrying near the bottom. Set the bottom limit so the seal is compressed but the bar does not rest on the sill.
Does a battery screen motor have obstacle detection?
Somfy's and Simu's solar screen motors stop on an obstacle, as covered in battery vs hardwired screen motors. The same rule applies: it protects the screen, so check your motor's manual.
Sources and standards consulted
- EN 13561:2015, External blinds and awnings: performance requirements including safety (CEN)
- Lateral arm and cassette awning technical manuals (arm, spring and torsion bar specifications) (manufacturer documentation)
- Tubular motor technical data sheets (torque, speed, duty cycle, thermal protection) (manufacturer documentation)
See how we research for our sourcing and verification process.