How to make solar screens for windows

To make a solar screen, you build an aluminum frame to the window's size, press solar mesh into a groove around it with a rubber cord, and clip the frame over the outside of the window. Measure first and take off the clearance your mounting method needs: 1/16 in off the width and 1/8 in off the height for turn clips, 1 in off the width and 1/8 in off the height for brick grips. Then cut the frame, join the corners, roll in the mesh and trim it. One 36 x 60 in screen from a complete kit costs about $48 before mounting hardware. Add a crossbar on anything bigger than 3 x 4 ft.

Key takeaways

  • A common DIY kit frame is 5/16 x 1 in at .024 gauge with solid corners that fit over the ends, so nothing is mitered (Quality Window Screen's Textilene 80 kit).
  • Hardware store frame stock is often 3/8 x 3/4 in at .020 gauge. Prime-Line lists .185 in spline for fiberglass in it. Thick solar mesh takes one spline size smaller.
  • Austin Energy's rebate asks for a 3/8 x 3/4 in (or 5/16 x 3/4 in) frame at 0.020 gauge, mitered metal corners and a participating contractor. A kit with slip-on corners, built by you, does not meet it.
  • Mount it outside the glass. Inside, a solar screen does a fraction of the job: shading coefficient 0.50-0.70 against 0.14-0.33 outside.
  • A screen on a bedroom escape window must come off from inside without tools. Clips on the outside do not.

What a solar screen is, and why it is built like an insect screen

A solar screen is a window screen made with a thick, tightly woven, vinyl-coated polyester fabric in place of insect mesh. It stops most of the sun's heat outside the glass, before it can warm the room, and Textilene and SunTex are the two fabrics you will meet most.

The build is the same as an ordinary window screen. A frame of thin aluminum tube, called frame stock, has a groove along one face, the spline channel. You lay the mesh over the frame and press a round rubber cord, the spline, into that groove with a small wheeled tool, where it pinches the mesh in place.

Three numbers describe frame stock. A frame sold as 5/16 x 1 in is 5/16 in thick and 1 in wide. The gauge is the thickness of the aluminum wall, such as .024 in or .020 in, and a thicker wall makes a stiffer frame. Solar mesh is much thicker than insect mesh, and that changes the spline size, the corners you can use and how long a side can be before it bows.

Frame specs: the kit, the hardware store and the rebate

Most step-by-step guides say "buy frame stock" and stop there. The three published specs below do not agree, and the difference matters if you hope for a rebate.

Solar screen frame specs as published (sources linked below the table)
SourceFrame profileGaugeCornersOther
Quality Window Screen Textilene 80 kit5/16 x 1 in.024 ("heavy duty")External solid corners, "no miter cuts required"2 leaf springs, 2 lift tabs, spline and roller tool; crossbar "recommended over 3'x4'"
Prime-Line Make-2-Fit frame stock3/4 in wide x 3/8 in thick.020Bought separatelySpline not included; .165 in for aluminum mesh, .185 in for fiberglass
Austin Energy rebate rule3/8 x 3/4 in, or 5/16 x 3/4 in where the mounting will not take 3/80.020"Mitered and use metal, NO plastic corner braces"Center bar 5/16 or 3/8 x 5/8 in, 0.020; mesh deflects no more than 1/4 in

The kit figures are from Quality Window Screen's Textilene 80 solar screen kit page. The frame stock is Prime-Line's PL14059, as listed by True Value. The rebate rule is on Austin Energy's solar screens page.

A common claim is that a DIY frame loses the rebate because it is too thin. On these figures that is the wrong reason. The kit's .024 wall is thicker than Austin's 0.020. What the kit does not match is the 3/4 in width and the corners, which slip over the frame ends where Austin asks for mitered metal corners. The bigger point comes first, though: Austin says "You must use a participating contractor to install the equipment to qualify." A screen you build and hang yourself does not qualify in Austin at any gauge. Other utilities write their own rules, and six programs are compared in solar screen tax credits and rebates.

Tools and materials

  • Frame stock and four corners, or a kit that has them
  • Solar mesh, cut a few inches larger than the frame each way
  • Spline in the right size, and a spline roller
  • Hacksaw and miter box (Salt River Project's guide uses both), plus safety glasses and gloves
  • Tape measure, pencil, utility knife, flat screwdriver
  • Mounting hardware: turn clips and screws, brick grips, or the kit's leaf springs and lift tabs

Choose the mesh first: 80 or 90 percent

The number in the fabric name is not a measured percentage: Twitchell says Textilene 80 "blocks up to 80% of the sun's rays." Phifer's own card puts SunTex 80 at about 25% open and about 75% UV blocked. The 90 grades are tighter: SunTex 90 is about 10% open.

The trade is daylight against heat. SunTex 90 lets through about half the visible light of SunTex 80 (18-20% against 36-39%). Converted to SHGC, the share of the sun's heat that gets through the window, Textilene 80 lands near 0.29 and Textilene 90 near 0.20. Pick 80 for windows where you want light and a view, and 90 for west and south glass where low sun and glare are the problem. Both are set out in SunTex 80 vs 90, and the two brands side by side in Textilene vs SunTex.

Color counts as much as the grade. Efficient Window Coverings says color "can change the shading performance by as little as 5% or as much as 100%," and recommends "black screens for best shading/cooling performance" outside.

Measure the opening for your mounting method

Decide how the screen will hold on before you measure, because each method takes a different amount off. Quality Screen Company publishes two methods.

Turn clips screw into the window frame and rotate over the screen's edge. Its turn clip guide uses four, "two on each side about 6" to 8" from the top and bottom." Mark each clip spot with a 5/16 in circle, then measure the width between the circles, inside edge to inside edge, and "subtract 1/16 of an inch." Measure the height of the window frame and "subtract 1/8 of an inch." The guide also asks you to check there is about 3/4 in of aluminum window frame on each side, so the screws miss the glass.

Brick grips hold the screen in a brick opening with no screws. Its brick grip guide measures from the inside edge of the brick on one side to the other, then subtracts one inch. Height is the window frame minus 1/8 in, and the grips are made for a 5/16 in thick frame and take four to six per screen.

Channel mount is the third way. The frame sits in the window's own screen channel, held by leaf springs (curved metal strips that push the frame into the channel). Salt River Project says that if the window has a channel, measure from inside it. That is the setup the kit's leaf springs and lift tabs are for.

Write the finished size on paper before you cut. The general measuring habits, three readings and use the smallest, are in how to measure for retractable screens.

How to make the screen, step by step

This follows Salt River Project's eight-step method (June 2021), with the figures it leaves out added from the sources above.

  1. Measure the window. Take the finished screen size from your mounting method above.
  2. Take off the corners. SRP says to "subtract the size of the frame corners" from both measurements. The amount depends on the corner, so measure yours. Push a corner onto a scrap of frame and measure how far it sticks out past the end, because each piece loses that amount at both ends. With mitered corners, the frame pieces are cut to the full outside size, at 45 degrees.
  3. Cut the frame. Use a hacksaw and a miter box, with glasses and gloves on, and cut the two sides together and the top and bottom together, so each pair matches. File off any burrs.
  4. Build the frame. Push the corners in so "the spline channel is on the inside of the frame and facing up." Check that it is square by measuring both diagonals, which should match, and fit the crossbar now if the screen gets one.
  5. Lay the mesh over the frame. Roll the mesh out and trim it, leaving extra on every side to hold while you work.
  6. Roll in the spline. Start at one corner and use the roller to push the spline and mesh into the channel along one side. Do the opposite side next, pulling the mesh just snug, then the other two. Do not stretch it so hard the frame bows in. Austin's test is a good target: pressed gently, the mesh should give no more than 1/4 in.
  7. Trim the waste. Cut off the extra mesh with a utility knife, along the outer edge of the spline. Or tuck it in with a screwdriver, as SRP suggests.
  8. Mount the screen. Fit the lift tabs, then fix the screen with clips, grips or leaf springs.
Spline for thick mesh: Solar mesh fills more of the channel than fiberglass insect mesh. Twitchell gives Textilene 80 as .0328 in thick. Streme's standard fiberglass mesh is about 0.30 mm (.012 in), as noted in no-see-um mesh size. So go one spline size smaller than the frame maker lists for fiberglass. On Prime-Line stock that means stepping down from .185 in. Our spline size guide has the full size table. Test a short length first, though a kit that says "correct size spline" has already done this.

Add a crossbar on tall frames

A crossbar is a piece of frame stock run across the middle of the screen and held at each end with clips. It stops the long sides bending in under the pull of the mesh. Quality Window Screen recommends one on any screen "over 3'x4'" and sells it with two crossbar clips for $1.00 more. Austin's rule names a center bar of 5/16 or 3/8 x 5/8 in at 0.020 gauge.

Put it at mid-height: the turn clip guide measures "from the base of the window all the way up to the middle," and says "the crossbar goes to the inside," the side facing the glass. On a brick opening, two of the grips go at the crossbar.

Worked example: one 36 x 60 in window

Worked example: Take a west window with an aluminum frame. Suppose the clip circles are 36 in apart and the window frame is 60 in tall. With turn clips, the finished screen is 36 - 1/16 = 35-15/16 in wide and 60 - 1/8 = 59-7/8 in tall. That is about 15 sq ft of mesh.

Kit size. 35-15/16 x 59-7/8 in fits the "up to 3' x 5'" Textilene 80 kit. That is the $35.95 base plus $11.00, so $46.95.

Crossbar. The screen is taller than 4 ft, so add the $1.00 crossbar. Center it about 29-15/16 in from the bottom, and the kit is now $47.95.

Mounting. Die-cast casement turn clips are $18.95 for a bag of 25. Self-tapping screws for aluminum window frames are $6.95 for 25. That brings the first window to $73.85. A bag of 25 clips covers six windows at four clips each, so across six windows the hardware adds about $4.32 a window. On a brick opening, EZ Brick Grips are $25.00 for 25, with no screws.

Rebate. In Austin, 15 sq ft at $1.00 per sq ft would be $15.00. It is not available here, because the screen is self-installed and the kit's corners are not mitered.

Prices are Quality Window Screen's listed prices, read on 15 November 2026, before shipping and tax. Wood window frames need different screws: the clip page recommends No. 8 Phillips pan head sheet metal screws for wood.

Inside or outside the glass, and inside or outside the frame

"Inside mount" means two different things, and mixing them up costs heat. One is which side of the glass the screen is on. The other is whether the screen sits inside the window's frame recess or on its face.

Glass side. Put a solar screen outside the glass. Efficient Window Coverings gives exterior solar screens a shading coefficient of 0.14-0.33. The same screens inside the glass score 0.50-0.70, because the heat is already in the room. Its rule converts that with SHGC = 0.87 x SC. It also says exterior screens are "not appropriate for outward swinging windows," since the sash cannot open into them.

Frame side. Turn clips and leaf springs hold the screen within the window frame, and brick grips set it in the brick opening, so all of them stay outside the glass. Clips screwed into a window frame can raise warranty questions, covered in do solar screens void a window warranty.

Retract Wise analysis: The frame spec decides more than the mesh does. A 5/16 x 1 in kit frame is wider and has a thicker wall than the 3/8 x 3/4 in stock in a hardware store. That suits thick solar mesh pulled tight over a 5 ft side. But it is not the frame a rebate program like Austin's names. Decide which you want before you buy: if a rebate is the goal, call the utility first, since Austin's needs a contractor whatever you build. If not, the kit's heavier frame and crossbar are the safer DIY choice for anything over 3 x 4 ft.

Bedroom windows: keep it removable from inside

A bedroom's escape window must stay usable in a fire. Section R310.4.4 of the 2021 International Residential Code says a screen over it must be "releasable or removable from the inside without the use of a key or tool." A clip-on exterior solar screen fails that, because the clips are outside. The full test, with each screen type checked, is in solar screens on egress windows.

What this guide does not cover

This is a build for flat, fixed screens that clip over a window. Roll-up and motorized solar screens use different fabric, housings and side channels, and are not built this way. Retractable options are in retractable window screens.

The frame figures are one kit, one brand of frame stock and one utility's rule. Other makers' frames, corners and clip deductions differ, so use the numbers on your own parts. The prices are one seller's on one day. The rebate ruling is Austin's alone; check your own utility's page before you buy. The egress rule is the 2021 IRC as quoted on our egress page, and your local code and inspector decide. Nothing here rates a screen for wind or storms.

Sources

Frequently asked questions

Is it cheaper to make your own solar screens?

A complete Textilene 80 kit for a screen up to 3 x 5 ft is $46.95 at Quality Window Screen, plus $1.00 for a crossbar and a few dollars a window in clips. You supply the labor. Custom-built screens and installed prices vary too much by area to quote here.

What size frame do you use for solar screens?

Quality Window Screen's kit uses 5/16 x 1 in frame at .024 gauge. Austin Energy's rebate rule names 3/8 x 3/4 in at 0.020 gauge, or 5/16 x 3/4 in where the window will not take 3/8. Hardware store stock such as Prime-Line's is 3/8 x 3/4 in at .020.

What spline do I use for solar screen fabric?

One size smaller than the frame maker lists for fiberglass mesh, because solar fabric is thicker. On Prime-Line stock that lists .185 in for fiberglass, step down one size and test a short piece. Sizes are in our spline size guide.

Do I need a crossbar on a solar screen?

Quality Window Screen recommends one on screens over 3 x 4 ft. Fit it at mid-height, on the side facing the glass.

Can I put a DIY solar screen inside the window?

You can, but it blocks far less heat. Efficient Window Coverings gives solar screens a shading coefficient of 0.14-0.33 outside the glass and 0.50-0.70 inside.

Does a homemade solar screen qualify for a utility rebate?

Not in Austin, where a participating contractor must install the screens and corners must be mitered metal. Other programs have their own rules; check your utility's page.

Sources and standards consulted

  • International Residential Code (IRC), wood framing and fastening provisions (ICC)
  • NFPA 70, National Electrical Code (outdoor receptacles, GFCI and wet location requirements) (NFPA)
  • Anchor manufacturer technical guides for masonry and concrete fastening (edge distance, embedment) (manufacturer documentation)
  • Manufacturer installation manuals for awnings, retractable screen doors and motorized screens (manufacturer documentation)

See how we research for our sourcing and verification process.