What mesh size keeps out no-see-ums?
For a retractable screen, 20x20 vinyl-coated fiberglass is the mesh that keeps out no-see-ums. Its holes are about 0.036 in (0.91 mm) square, against roughly 0.043 x 0.050 in (1.1 x 1.3 mm) for standard 18x16 fiberglass, which midges get through. The "you need 30x30" advice is right for metal wire cloth and wrong for fiberglass: a 20x20 wire mesh has thinner strands and a bigger 0.041 in (1.04 mm) hole, so wire has to go finer to reach the same opening. The price of the smaller hole is airflow, and on a roll-up screen, a fatter roll.
Key takeaways
- Clemson Extension recommends "a very fine mesh screening (20×20 mesh or smaller)" against biting midges, which it puts at around 1/16 in long.
- Mesh count is not hole size. A 20x20 fiberglass hole (0.91 mm) is closer to a 24x24 wire hole (0.86 mm) than to a 20x20 wire hole (1.04 mm), because the coated yarn is thicker.
- In a 1959 field study, a screen with 1.6 mm² openings cut midge entry by only 56%. Standard 18x16 fiberglass works out at about 1.4 mm² per hole.
- The finer weave costs air: Streme lists 42% open area for its 20x20 fiberglass, against 63% for its standard 18x16.
- The mesh is only as good as the edges. A worn brush seal, a cable-guided side or a torn corner lets midges round a 20x20 mesh.
Hole size by mesh: the numbers side by side
Mesh count is strands per inch in each direction. The hole is what is left between strands, so the same count gives a different hole with a different strand. Vinyl-coated fiberglass, the usual mesh in retractable screens (see screen mesh types), has a much thicker strand than stainless or bronze wire cloth. The table puts the published openings in one place.
| Mesh | Material | Strand | Hole | Open area | No-see-ums |
|---|---|---|---|---|---|
| 18x16 standard | Vinyl-coated fiberglass | about 0.012 in (0.31 mm), calculated; 0.30 mm thick | about 0.043 x 0.050 in (1.1 x 1.3 mm), our calculation | 63% | Get through |
| 20x20 wire | Metal wire cloth | 0.0090 in (0.228 mm) | 0.041 in (1.04 mm) | 67.2% | Borderline |
| 20x20 fiberglass | Vinyl-coated fiberglass | 0.33 mm yarn, 0.381 mm thick | 0.036 in (0.914 mm) | 42% (listed) | Recommended |
| 22x22 wire | Metal wire cloth | 0.0075 in (0.190 mm) | 0.038 in (0.965 mm) | 69.7% | Recommended |
| 24x24 wire | Metal wire cloth | 0.0075 in (0.190 mm) | 0.034 in (0.864 mm) | 67.2% | Recommended |
| 30x30 wire | Metal wire cloth | 0.0065 in (0.165 mm) | 0.027 in (0.686 mm) | 64.8% | Recommended |
The fiberglass 20x20 row comes from Streme's 20x20 technical specification, which lists a 0.33 mm yarn, an aperture of 0.9144 x 0.9144 mm (0.839 mm²) and 42% open area, and calls the mesh "ideal for protection against No-See-Ums, Gnats, Sand Flies, and other tiny insects." The 18x16 row uses its standard fiberglass specification (0.30 mm thick, 63% open area). Streme lists no hole for 18x16, so we worked it out: a 0.31 mm strand gives 63% open at 18 and 16 strands per inch, leaving holes of about 1.10 x 1.28 mm. The metal rows are from Wovenwire's no-see-um screen table. The "borderline" verdict for 20x20 wire is ours, because its hole is larger than the fiberglass 20x20.
One figure does not add up: Streme's aperture, 0.839 mm² in a 1.27 mm cell, works out to about 52% open, not the 42% it lists. Treat the open-area column as each maker's own figure, not a like-for-like test. Openness and what it does to light and air are explained in screen mesh openness factor.
Why standard screen lets them in
The University of Florida's Featured Creatures profile of biting midges puts adults at "usually 1.0 mm to 2.0 mm (0.04 to 0.08 in) long" and says plainly that "regular window screens do not exclude biting midges from indoor areas." The University of Arizona's Backyard Gardener sheet (January 2023) says adults "can easily pass through normal window screens" and come in "through standard 16 mesh screening and netting or damaged areas of the screen."
The one measured test we found is old but direct. J. F. Porter's 1959 study of screens against C. furens is summarized in a 2015 paper by Baker and colleagues in Parasites & Vectors: Culicoides "can pass through untreated insect screens with mesh sizes of 1.6 mm²," though those screens "did reduce Culicoides entry rates by 56 %." Standard 18x16 fiberglass, at about 1.4 mm² a hole, sits close to that. Expect it to slow midges down, not stop them.
Length is a poor guide: a midge 1-2 mm long sounds bigger than a 1.1 mm hole, but it goes through head first, so its width is what has to fit. Wovenwire's rule is to "select an opening slightly smaller than the pest you wish to exclude."
20x20 or 30x30: why both numbers circulate
Both answers come from real sources. Clemson's Home & Garden Information Center (Justin Ballew, October 2018) says biting midges need "a very fine mesh screening (20×20 mesh or smaller)." The 30x30 figure belongs to the wire cloth world, where a 20x20 hole is 1.04 mm and Wovenwire's no-see-um range runs from 20 to 42 mesh.
For a retractable screen the choice is already made. Roll-up and pleated screens use coated fiberglass or polyester, not wire, because metal creases on a roller. No-see-um fiberglass is woven at 20x20 (Streme's is), and its 0.91 mm hole is smaller than a 20x20 wire hole and only about 0.05 mm bigger than a 24x24 wire hole. Where a 30x30 wire mesh fits is a fixed frame, such as a porch panel or a window that never rolls.
What fine mesh costs you
Air. Going from 63% to 42% listed open area is a third less open face, and the Baker paper notes that fine mesh is "associated with a significant reduction in airflow" in the stables it studied. Put 20x20 on the openings that face the marsh, the water or the prevailing evening breeze, and keep standard mesh elsewhere, as suggested for enclosures in porch and lanai screen enclosures.
Roll size. Streme's 20x20 is 0.381 mm thick against 0.30 mm for its standard mesh, about 27% thicker. Each wrap adds twice the thickness to the roll diameter.
Makers do restrict it. Genius caps its Milano 100 roll-up door at 50 in wide with No-See-Um mesh, against 60 in for its standard mesh (more maker limits in retractable screen door sizes). Pleated doors have their own limits (see pleated vs roll-up screen doors).
The gaps around the mesh matter as much
A retractable screen has sliding edges a fixed screen does not, and each is a path around the mesh. Check these before blaming the mesh:
- Side tracks. Brush pile in the channels should lightly touch the mesh along its whole height. Flattened or missing pile leaves a slot wider than any mesh hole; measuring and replacing it is covered in brush seals and pile weatherstrip.
- Bottom bar and threshold. Low-profile floor tracks on uneven floors leave a gap under the bar. A sweep closes it.
- Cable-guided screens. A cable holds only the bottom bar, so fine mesh on a cable-guided screen still leaves the sides open; a zip screen locks them (see zip vs cable-guided screens).
- Damage. The Arizona sheet names "damaged areas of the screen" as an entry point. A split along the spline or a nick at the bottom bar is enough.
If you are swapping the mesh yourself, the procedure is in how to rescreen a retractable screen. A thicker mesh may need a smaller spline (see the spline size guide), and on a spring screen the heavier roll can change how firmly it retracts, which retractable screen spring tension explains how to adjust.
When mesh is not enough: fans and treated screens
Midges are weak fliers. Clemson says a ceiling fan on a covered porch or a box fan "can help keep gnats away, as they are small enough to be blown off course by air movement." UF/IFAS's Biting Midges of Coastal Florida (ENY-629) recommends increasing "air movement in screened porches by using high velocity fans," and says screens "can be treated with barrier sprays or portable foggers according to the label for temporary reductions in small backyard situations." A fan also gives back some of the airflow the fine mesh took away.
UF/IFAS says most biting midges bite "during dusk, night, or morning," which is when the screen has to be down and the edges sealed.
Where this stops applying
- No test of 20x20 fiberglass against midges. We found no published study that puts 20x20 fiberglass in front of Culicoides and counts what gets through. The recommendation rests on extension advice and hole sizes, not a measured pass rate.
- Porter's study is from 1959 and tested one species, C. furens, in Florida. Its 1.6 mm² figure is as Baker and colleagues report it.
- Hole sizes are one maker each. Streme's fiberglass and Wovenwire's wire figures are typical, not universal. Another maker's 20x20 with a thinner coat will have a bigger hole.
- Solar and privacy fabrics are rated by openness, not mesh count, and we found no hole sizes for them, so they are not in the table.
Bottom line
Buy 20x20 vinyl-coated fiberglass for a retractable screen where no-see-ums bite: its 0.91 mm hole is smaller than a 20x20 wire hole, so the "30x30" advice does not apply to it. Put it where the midges come from, confirm the maker offers it for your housing and width, and seal the edges, because a midge that cannot get through the mesh will go round it.
Frequently asked questions
Will 18x14 or 18x16 screen keep out no-see-ums?
No. Both have holes around 1.1 mm or larger, and UF/IFAS, Arizona and Clemson all say standard screen does not exclude biting midges.
Is 20x20 mesh small enough for no-see-ums?
Clemson Extension recommends 20x20 or smaller. In vinyl-coated fiberglass the hole is about 0.91 mm (0.036 in), smaller than 20x20 wire cloth at 1.04 mm.
Do I need 30x30 mesh?
Only in metal wire cloth, where 20x20 has a larger hole. In the fiberglass used in retractable screens, 20x20 already has a smaller hole than 20x20 wire.
Can I put no-see-um mesh in my existing retractable screen?
Often, but check first. It is thicker, so the roll grows, and some makers limit width with it (Genius: 50 in instead of 60 in on the Milano 100). Ask the maker whether 20x20 is an approved option for your model.
Sources and standards consulted
- Screen mesh specification sheets (fiberglass, aluminum, polyester and PVC-coated meshes) (manufacturer documentation)
- Spline and screen frame channel specifications (manufacturer documentation)
- Retractable screen and zip screen component catalogs (manufacturer documentation)
See how we research for our sourcing and verification process.