Bond Bridge Pro vs Somfy TaHoma for motorized screens: which hub do you need?

Choose by the motor in the screen, not by the app. If every motor in the house is Somfy, RTS or Zigbee, get a Somfy TaHoma Switch: it is the only one of the two that can drive Somfy's Zigbee motors. If any screen runs on a Rollease Acmeda, Gaposa, Nice or Dooya motor, or the house mixes brands, get a Bond Bridge Pro, which copies the radio remotes of more than 30 shade motor brands, Somfy RTS included. Neither hub can tell you where a Somfy RTS screen actually is. RTS is one-way radio, and Bond's position slider works by timing the motor, not by asking it.

Key takeaways

  • TaHoma Switch: up to 40 RTS channels and 60 Somfy Zigbee products, and up to 10 units can be joined for RTS. Somfy's earlier spec sheet for the TaHoma RTS/Zigbee interface (copyright 2021) said 50 Zigbee devices, so that figure is out of date.
  • Bond Bridge Pro: up to 50 devices over about 3,500 sq ft, $379, with Ethernet and PoE. Its radio covers 300 to 450 MHz only, so it cannot reach a 2.4 GHz Zigbee motor.
  • Somfy RTS runs on 433 MHz, which both hubs cover. For an RTS-only house, either hub works, and the choice comes down to integrations and placement.
  • Bond's "Set Position" for Somfy RTS is Bond Bridge Pro only. It estimates position by dead reckoning, and using the original remote throws the estimate off.
  • The earlier TaHoma interface's spec sheet rates it IP 30, "for indoor use only," at 32°F to 95°F. Bond sells a Shield Pro enclosure for mounting the Bridge Pro outdoors.

Bond Bridge Pro vs TaHoma at a glance

Somfy TaHoma Switch vs Bond Bridge Pro (figures from the Somfy and Bond documents linked in the sections below)
QuestionSomfy TaHoma SwitchBond Bridge Pro (BD-1750)
Motor radiosSomfy RTS (433 MHz), Zigbee 3.0 (2.4 GHz)Sub-GHz RF, 300-450 MHz (North America, with two bands excluded)
Motor brandsSomfy onlySomfy RTS, Rollease (ARC and Basic), Nice, Dooya, Gaposa, Coulisse/Motion Blinds and 25+ more
Capacity40 RTS channels, 60 Zigbee products50 devices
Larger housesJoin up to 10 units (RTS only)Several bridges per job; 3,500 sq ft RF reach each
Commands to an RTS motorUP, DOWN, MY, STOPOpen, close; Set Position by timing (Pro only)
Position read back from RTSNoNo
Network2.4 GHz Wi-Fi; optional Ethernet adaptor2.4 GHz Wi-Fi or Ethernet; PoE
MountingBase stand; IP 30, indoor only (earlier model's sheet)Ceiling or wall; Shield Pro enclosure for outdoors
Apple HomeSelect Zigbee motors onlyThrough Homebridge
Warranty5 years3 years
PriceThrough Somfy dealers, no list price on Somfy's page$379

Does a Somfy screen need a Somfy hub?

Two answers circulate: that a Somfy motor needs a Somfy hub, and that a Bond Bridge controls anything with a remote. Each is half right, and which half depends on the radio inside the motor.

Bond's own Bridge Pro spec sheet calls it a "Sub GHz to Wifi (TCP/IP) Bridge" covering remote controls between 300 and 450 MHz. In North America the 321.5-336.0 MHz and 399.5-410.5 MHz bands are excluded. Somfy RTS runs on 433 MHz, according to Somfy's TaHoma RTS/Zigbee spec sheet, so it sits inside Bond's range, and Bond lists Somfy in "RTS Roller Mode" on its supported brands page. An RTS screen does not need a Somfy hub.

Somfy's Zigbee motors are different. Zigbee 3.0 runs at 2.4 GHz, outside anything the Bond Bridge Pro transmits, and Zigbee does not appear on Bond's brand list. A screen with a Somfy Zigbee motor needs TaHoma. The myth that Bond "does everything" comes from its long brand list, which really is long, but every brand on it is a sub-GHz remote that Bond copies. That is also why both claims keep circulating: on an RTS-only install, either hub really does work. Somfy's two radio families are explained in RTS or io.

Which hub for which screen motor

Find the motor brand on the motor label, in the screen's manual or on the remote, then read across. The brands below are the motor makers you will meet on patio and zip screens; the screen makers that use them are listed in our retractable screen brands guide.

Hub by motor (Retract Wise assembly from Somfy's TaHoma Switch page and Bond's supported brands page)
Motor in the screenTaHoma SwitchBond Bridge ProPick
Somfy RTS onlyYes, 40 channels per unitYes, RTS Roller ModeEither; TaHoma if you may add Zigbee later
Somfy ZigbeeYes, 60 productsNo (2.4 GHz)TaHoma
Somfy RTS plus ZigbeeYes, both on one unitRTS onlyTaHoma
Rollease Acmeda (ARC or Basic)NoYesBond
GaposaNoYesBond
Nice (F-Code and O-Code)NoYesBond
Dooya, Coulisse/Motion Blinds, A-OKNoYesBond
Progressive Screens MagnaTrackNot as a systemYes (MagnaTrack bridges)Bond
Somfy RTS mixed with any brand aboveSomfy screens onlyAll of themBond
Somfy Zigbee mixed with another brandSomfy screens onlyOther brands onlyBoth hubs

The MagnaTrack row is the clearest sign of which way screen makers lean. Progressive Screens' MagnaTrack screens are "driven by Gaposa and Somfy motors," and since April 2023 two bridges co-developed with Bond, the BD-1720 and BD-1740, have been their only control hubs. Residential Systems reports that each controls up to 50 MagnaTrack screens in a 3,500 sq ft location and that they were "born from the Bond Bridge Pro." CE Pro calls them "MagnaTrack's sole hubs for control." A screen maker that fits two motor brands needs a hub that speaks both, and TaHoma speaks only Somfy.

Worked example: a lanai has three Somfy RTS zip screens from the original build and two Rollease Acmeda screens added later by another dealer. A TaHoma Switch can run the three Somfy screens and nothing else, so the Rollease screens stay on their own remote. One Bond Bridge Pro runs all five, well inside its 50-device limit, and runs them all from one app. Swap the Somfy screens for Zigbee models and the answer changes: TaHoma for the Somfy screens, Bond for the Rollease screens, two apps.

Neither hub knows where an RTS screen is

RTS is one-way. The remote or hub sends a command, the motor acts on it, and nothing comes back. A Bond staff member put it plainly on Bond's forum in March 2023: "RTS motors are one-way. There's no way to read the motor position." That holds for TaHoma too. Its spec sheet lists UP, DOWN, MY and STOP for motorized shades, and MY is the one intermediate position stored in the motor (the same MY button used to save limits in how to reset the limits on a motorized screen). For RTS, Somfy's TaHoma Switch page talks of "timed events to automatically position RTS shading," which means sending one of those commands at a set time, not reading a position back.

Bond's position slider gets around this by estimating. Bond staff wrote in an older thread that Somfy's RTS protocol "doesn't support specifying a position via RF." In December 2021 Bond added a SetPosition option for Somfy RTS on the Bond Bridge Pro, which, in the staff member's words, "uses deadreckoning, but it's pretty good." It works by timing. You enable Set Position and run a calibration in the app. After that, the Bridge keeps "a confidence interval of where the Bridge thinks the shade is" and will "eventually move the shade to one of the rails to reduce the ambiguity." It is Bond Bridge Pro only, not the standard Bond Bridge.

Two consequences for screens:

  • Do not mix the remote and the slider. Bond's staff warn that once Set Position is on, "you won't be able to use the remote without confusing the Bridge." A Bond-controlled RTS screen should be run from the app, voice or a Bond-paired control, not the original Somfy remote.
  • A hub cannot confirm the screen is up. An app showing "open" for an RTS screen is showing the last command sent. If a screen must be up before a storm, check it by eye, or rely on a wind sensor paired with the motor. How those sensors work is in sun and wind sensors, and what a zip screen can stand when left down is in zip track screen wind resistance.
Partial drops on zip screens: a dead-reckoned stop halfway down is an estimate. On a solar zip screen used for afternoon glare, being a few inches off does no harm. If the screen has to stop at an exact height every time, set MY on the motor and call MY, which the motor stores itself.

Capacity: 40 channels or 50 devices

An RTS channel is one address a remote or hub can send to. One screen per channel gives individual control, and a group of screens can share a channel, but then they always move together. TaHoma gives 40 RTS channels per unit, and Somfy's TaHoma Switch page allows up to 10 units to be joined "for multi-zone control (RTS)," 400 channels in all. The joining applies only to RTS. The earlier spec sheet also caps a TaHoma at 40 scenes and 40 schedules.

The Bond Bridge Pro controls up to 50 devices across a 3,500 sq ft RF reach. The standard Bond Bridge, by Bond's comparison on the spec sheet, covers 30 devices and 2,500 sq ft with a 1-year warranty (Pro: 3 years), and it lacks Ethernet, PoE and the position slider. For a big screened porch, pool cage or several detached structures, the MagnaTrack bridges show the pattern: more than one bridge on larger jobs.

Where each hub can go

Somfy's spec sheet for the earlier TaHoma interface rates it IP 30, "for indoor use only," with an operating range of 32°F to 95°F (0-35°C), and it ships with a base stand. Somfy's TaHoma Switch page lists its uses as interior window coverings and pergolas. Somfy offers an Ethernet adaptor for a wired network link and does not recommend third-party ones.

The Bond Bridge Pro mounts on a ceiling or wall, runs from PoE or 3 V DC at 1 W, and has a 6 ft cable. Bond's product page pairs it with the Shield Pro enclosure for outdoor installation. That matters on a lanai or detached pergola where the closest indoor shelf is behind a brick wall: a PoE cable can carry both power and data to a ceiling mount close to the screens.

If the screens are still being specified, plan the hub location with the motor wiring. The runs to each head box are covered in installing motorized patio screens, and a network drop for the hub costs little at the same time.

Voice, apps and home automation

Both hubs work with the mainstream platforms. Where they differ, it is Apple Home and the professional systems each supports.

Integrations listed by each maker (Somfy TaHoma Switch and integrations pages; Bond product page and spec sheet)
PlatformTaHoma SwitchBond Bridge Pro
Amazon Alexa, GoogleYesYes
SmartThingsYesYes
Apple Home"Only supported for TaHoma switch used with select Zigbee technology motors"Through Homebridge
Control4, Crestron, Savant, ELAN, RTI, URCYes (drivers give access to RTS channels and scenes)Control4, Crestron, Savant, RTI, URC listed; drivers for C4, Elan, RTI, URC
Hubitat, local APISomfy Synergy API (earlier sheet)Hubitat; "Open Local API"
OtherPhilips Hue, Brilliant, Alarm.com, Sonos, Josh.aiJosh.ai (MagnaTrack bridges), Basalte, Nice Home

On Somfy's Alexa page, TaHoma's skill controls "RTS channels, scenes, schedules," with commands like "Alexa, raise kitchen blinds." Somfy's integrations page says the Control4, Crestron, Savant, ELAN, URC, RTI and Alarm.com drivers give "access to RTS channels and scenes programmed by the TaHoma North America app." On either hub, a professional system sees the same commands the app does. It adds no position feedback for RTS.

For an iPhone household with RTS screens, this is the one case where Bond has the edge even on an all-Somfy install: TaHoma's Apple Home support is for Zigbee motors only, while Bond reaches Apple Home through Homebridge.

Which to choose

  • TaHoma Switch: every motor is Somfy, any of them is Zigbee, or you want one maker to answer for both motor and hub.
  • Bond Bridge Pro: any Rollease Acmeda, Gaposa, Nice or Dooya motor, a mix of brands, MagnaTrack screens, a hub that must mount outside or on PoE, an RTS position slider, or RTS screens in Apple Home.
  • Both: Somfy Zigbee screens in the same house as another brand.

Choosing the motor itself, and whether it runs on house power or a solar battery, comes first. Torque limits by screen size are in battery vs hardwired motorized screen, and motor sizing and control options are in our motorized patio screens guide.

When this comparison stops applying

  • Somfy io. io-homecontrol is Somfy's two-way radio, which reports status. Neither of the U.S. pages we read lists io for the TaHoma Switch, and Bond's brand list does not include it. An io screen is outside this comparison.
  • Hardwired or dry-contact control. A screen run from a wired switch or a dry-contact interface does not go through either hub's radio.
  • Figures change. The TaHoma figures come from Somfy's current TaHoma Switch page and the earlier interface's spec sheet; the Zigbee count has already gone from 50 to 60. Bond adds brands to its list over time. Check both pages before buying.
  • Brand names on a remote. A screen sold under one name may use another maker's motor. The label on the motor decides, not the logo on the remote.

Bottom line

All Somfy, with any Zigbee in it: TaHoma Switch. Any Rollease Acmeda, Gaposa, Nice or Dooya motor, or a mix of brands: Bond Bridge Pro, which also brings PoE, outdoor mounting and an RTS position slider. Somfy RTS only: either works, and Bond is the better pick for Apple Home. Whichever you buy, an RTS screen never reports where it is. The app shows the last command, and Bond's slider is a timed estimate.

Frequently asked questions

Can a Bond Bridge Pro and a TaHoma both control the same RTS screen?

Both can be set up on it, but each hub only knows its own commands. If Bond's Set Position is on, any command from TaHoma or a Somfy remote leaves Bond's estimate wrong until it next runs the screen to a limit.

Does the standard Bond Bridge work for screens?

For open, close and stop, yes: Bond lists the same motor brands for both models. The RTS position slider, Ethernet, PoE and the 50-device limit are Bond Bridge Pro only.

Will a hub raise my screens in high wind?

Not on its own. Neither hub's spec lists a wind sensor input for RTS screens. Wind protection comes from a sensor paired with the motor, and with RTS the hub cannot confirm the screen went up.

Sources and standards consulted

  • Energy Efficient Window Attachments (U.S. Department of Energy, Energy Saver)
  • EN 13561:2015, External blinds and awnings (CEN)
  • ASCE 7, Minimum Design Loads for Buildings (wind and snow loads) (American Society of Civil Engineers)

See how we research for our sourcing and verification process.