How do you raise a motorized screen when the power is out?

Only if the screen's motor is a manual-override type. Somfy's CSI and CMO motors and the "NHK" drives sold by Selve, Elero and Somfy have a crank input on the motor head, and with the power switched off a crank turns the tube through the motor's own gears. A standard tubular motor has no such input, and its brake holds the tube whenever the motor is unpowered. On that kind of screen nothing you do at the bottom bar will roll the fabric up, so do not pull or push the bar: the screen stays where it is until the power comes back.

Key takeaways

  • Look for "CSI", "CMO", "NHK" or "manual override" on the motor label, and for a crank eye at the motor end of the head box. No eye, no cranking.
  • The crank is usually extra. Somfy's LT 50 CSI instructions call for a crank with a 6 mm square or 7 mm hexagonal pin, "accessories not supplied," and Elero's NHK motors are listed with the handle "not included."
  • Switch the breaker off before cranking. Somfy: "Never operate the roller shutter or awning via the control point while using the emergency crank!"
  • Expect a lot of turns. At Somfy's 27:1 override ratio, an 8 ft screen takes roughly 250 crank turns; at 55:1, about 520.
  • A solar battery motor needs no crank: it never depended on house power in the first place.

Can yours be cranked? The motors that can

Manual override is a type of motor, not an accessory you add to any motor. The drive has a geared input in its head, and the crank engages that input through an eye, usually with a rod and universal joint. These are the override drives whose maker or dealer sheets we read.

Manual-override tubular motors: crank fitting, limits and what cranking does (sources: maker instructions and trade listings, October 2026)
MotorCrank fittingCrank supplied?Limit systemLimits after crankingCrank ratio
Somfy LT 50 / LT 60 CSI (same instructions cover LT 50/60 NHK and CMO)6 mm square or 7 mm hex pinNoPush buttons on the motor head, 34 turns of travelNot stated27:1 (LT 50), 55:1 (LT 60)
Somfy CMO (e.g. 525A2 RTS CMO)Override kit with crank handleSold as a kit"Rapid limit switch"Not statedNot stated
Selve SP-NHK, 7-120 Nm7 mm hex or 6 mm squareNot statedMechanical, "point to point," 22 turns"Remain unchanged"13:1
Selve SEE-NHKCrank rodNot statedAutomatic (electronic)Relearned automatically13:1
Elero VariEco M NHK, 30 and 40 Nm, 14 rpm7 mm hex and 6 mm square"Not included"MechanicalNot statedNot stated
Geiger Spindle, 30 Nm, 16 rpm, mechanical override"Standard crank"Not statedMechanical spindle, set with screwsNot statedNot stated
Becker E22 in its EscapeSetHand crank kept in a holder by the windowNot statedElectronic"No loss of end positions"Not stated

Sources: Somfy's LT 50 CSI installation instructions (ref. 5053403B), Hopkins Blinds' trade listings for the Somfy RDO50 CSI, the RDO CSI Vectran, the Elero VariEco M NHK 30 Nm and 40 Nm and the Geiger Spindle, Trivantage's Somfy CMO override kit, Selve's SP-NHK page and its freewheel press release (March 2025), and Becker's escape route folder (09/2026).

Most of these are sold for roller shutters and awnings. Somfy's instructions say the LT 50 CSI is "designed to drive roller shutters and awnings," and Becker's EscapeSet is a roller shutter product. Of the sheets we read, only the Geiger listing names screens outright, alongside shutters and awnings; Selve says the SP-NHK suits "almost all types of coverings." So an override on a zip screen is possible but not standard: if the screen was ordered without one, assume it does not have one until the label says otherwise. Somfy's U.S. motor family and labels are explained in the Somfy motors guide.

Why a standard motor will not let go

An ordinary screen motor locks the tube whenever it has no power. Somfy's Sunea Screen 40 io data sheet (4/16, 3/30, 9/16 and 13/10 versions, in Nm and rpm) gives the brake type of every version as "Spring," and nowhere mentions a crank or override. A spring-applied brake is released electrically when the motor runs and clamps the drive train the rest of the time, as explained under the brake in tubular motor internals.

Two plausible answers circulate. One says you can lift a screen by hand, because people picture a spring roller like a screen door. The other says no motorized screen can move without power. Both are half right. A motorized screen has no spring to help, and fabric only winds up if the tube turns, so lifting the bar just bunches fabric in the channels and loads the zip edge. But a motor with a crank input can be wound up by hand.

Do not force the bottom bar. On a standard motor, the brake is designed to hold the tube against the weight of the screen. Pulling the bar up or down by hand works against that brake through the fabric and the edges, which are the parts you can damage. A zip edge pulled out of its channel is a repair job (see retractable screen repair).

How to tell from the label or the head box

  1. Look at the motor end of the head box. An override motor has to expose its crank input, so there is an eye, or a 6 mm square or 7 mm hex socket, at that end, sometimes behind a cap in the end cover. A plain, sealed end cover with nothing to engage points to a standard motor.
  2. Read the label or the paperwork. The model names that mean a crank input are "CSI," "CMO" and "NHK" (the German trade abbreviation Selve, Elero and Somfy use for emergency hand-crank drives), and "Mech Override" or "manual override" in a dealer's description. Somfy's Sunea Screen 40 io sheet lists no override.
  3. Find the crank. Since the handle is often not supplied, check whether the installer left one. A crank must match the socket: 6 mm square or 7 mm hex on the drives above.

If the label is hidden, check the installer's invoice. Do not open the head box during an outage to find out.

How to crank an override screen up

These steps follow Somfy's "Operating the emergency crank" section for its CSI motors. For any other brand, use that maker's instructions; the sheets for Selve, Elero and Geiger that we read give no step-by-step procedure.

  1. Switch off the power supply. Somfy's first step. Do it even though the power is out, so the motor cannot start while the crank is in your hand.
  2. Clear the opening. Move anything that sits under the bar or in a channel.
  3. Hook the crank into the ring. Somfy's words: "Hook the Somfy emergency crank into the ring." On other override motors, engage the crank in the eye or socket on the motor head.
  4. Turn the crank and watch the bar. "Turn the crank to raise or lower" the screen. Try a few turns first to confirm the bar is rising, then keep going at a steady pace.
  5. Stop before the bar reaches the box. Leave the last inch for the motor to finish on its limit once power is back.
  6. Unhook the crank before switching the power back on. The control point and the crank are never used together.
Worked example: An 8 ft (2,440 mm) drop on a 78 mm tube. The roll grows from 78 mm to roughly 87 mm across as it winds up, so the average circumference is about π x 82.5 = 259 mm, and the tube turns 2,440 / 259 = about 9.4 times. At Somfy's LT 50 CSI override ratio of 27:1 that is about 254 crank turns; at the LT 60's 55:1, about 518; at Selve's 13:1, about 122. At one crank turn per second, that is roughly 4, 9 and 2 minutes. All are well inside the limit travel the sheets give: 34 tube turns for the Somfy LT 50/60, 22 for the Selve SP-NHK.

Does cranking upset the limits?

It depends on the limit system, and the sheet for your motor decides. Of the documents we read:

  • Selve SP-NHK, mechanical: "End positions remain unchanged after manual operation."
  • Selve SEE-NHK, automatic limits: "if, in an emergency or even inadvertently, the shutter has been cranked up manually, the SEE-NHK automatically relearns its end limits."
  • Becker E22 in the EscapeSet, electronic: "No loss of end positions after using the hand crank."
  • Somfy LT 50/60 CSI: the instructions explain how to set the push-button limits and how to crank, but say nothing about what cranking does to the limits.

None of the sheets we read says that cranking erases the limits. So after power returns, run the screen down and up once with the remote and watch both stops. If one stop is now wrong, readjust it as in how to reset motorized screen limits. A supply that cuts out twice in quick succession can also put some radio motors into programming mode, as that page explains.

Retract Wise analysis: The crank ratio is chosen for you unless you ask. Somfy's LT 60 CSI needs 55 crank turns per tube turn, twice the LT 50's 27, and Selve's 13 is half again. A higher ratio makes each turn lighter and the job longer: about 9 minutes against 2 for the same 8 ft screen. If you order an override, ask for the ratio.

If there is no crank: what to do instead

A screen on a standard motor stays where the outage left it. What matters is whether it can stay down in the weather you expect.

  • Wind. A zip screen's wind rating is for the screen held in its channels at a given size; whether yours is rated for the forecast is in when to retract a zip screen.
  • Frost. A mesh or solar zip screen caught down by a winter outage stays down until power returns; do not run it until you are sure it is not frozen in. The cold-weather rules are in can you leave a zip screen down in winter.

The real alternative to a crank is a motor that does not use house power. A solar battery screen motor runs from its own battery, so an outage does not stop it, Which screens are small enough for one is in battery vs hardwired motorized screens. For a new hardwired screen, ask for an override at quote time: motor choices for patio screens are in motorized patio screens, and the cover a screen warranty gives a motor is in retractable screen warranties.

Where this stops applying

  • Procedures are per brand. The cranking steps above are Somfy's for its CSI motors. Selve, Elero, Geiger and Becker pages we read describe the feature, not the procedure.
  • Battery and DC motors are not covered by the crank discussion; a flat battery is a charging problem, not an outage.

Bottom line

Look for CSI, CMO, NHK or "manual override" on the label and a crank eye at the motor end of the box. If both are there, switch off the breaker, hook in a crank with the right pin (6 mm square or 7 mm hex), and wind the screen up while watching the bar: a couple of hundred turns for a typical patio screen. If not, the motor's brake is holding the tube and the screen stays put until power returns. Do not force the bar.

Frequently asked questions

Can I add a manual override to my existing screen motor?

Not to the motor you have. The crank input is part of the motor head, so an override means a different motor, such as a CSI, CMO or NHK type, fitted to the tube.

Does the screen keep its limits after a power cut?

Yes: limits are stored in the motor, and on the sheets we read cranking does not erase them either. Run one full cycle when power returns to check.

Sources and standards consulted

  • Tubular motor troubleshooting, limit-setting and remote pairing guides (manufacturer documentation)
  • Lateral arm awning service manuals (pitch, arm and spring adjustment) (manufacturer documentation)
  • Retractable screen manufacturer service and re-tensioning instructions (manufacturer documentation)

See how we research for our sourcing and verification process.