Why does my zip screen have wrinkles?

Light ripples along the edges of a zip screen, where the fabric meets the zipper, are normal. They come from zipper and fabric winding at different diameters, and most should flatten after the screen has been down for 1-4 hours. Wrinkles that stay, run diagonally, sag across the width (a "smile") or sit on one side only are faults: an installation out of level or square, a bottom limit set too low, or a fabric panel made too wide or welded too hot.

Key takeaways

  • Leave the screen fully down for 1-4 hours before judging it. Rollease Acmeda calls edge ripples from being rolled up "inherent to roller systems."
  • The European fabric guideline (ITRS) shows slight wrinkles at the zip edge as allowable, because fabric and zipper "travel different distances" when they wind.
  • Diagonal or crosswise creases mean the box and channels are not level and square. Isotra's tolerance is 2 mm for the widths and for the diagonals.
  • Slack fabric with waves everywhere often means the bottom bar is resting on the sill.
  • Small ripples beside the zipper weld mean the weld was too hot. The fix is a new fabric panel, so it is a warranty question.

Normal or fault: the symptom table

Zip screen wrinkles by symptom (sources: ITRS guideline, Rollease Acmeda and Isotra manuals)
What you seeVerdictMost likely causeFirst check
Light waves along both edges after being rolled upNormalZip and fabric wind at different diametersLeave it down 1-4 hours
Small gathers at horizontal seams, faint crosswise marks near the topNormal (ITRS)Seam and tube-attachment thickness on the rollNone needed
Diagonal or crosswise creases that stayFaultBox or channels not level and squareMeasure widths and diagonals
Waves everywhere, fabric slackFaultBottom limit too low, bar on the sill, or bar too lightWatch the bar at the bottom
Edge ripples that never fadeFaultFabric off center, panel too wide, or channels too tightCheck centering and panel width
Sag across the width ("smile")FaultToo little side tension, or fabric not straight on tube or barCheck the fabric runs square
Fabric creeping toward one end of the tubeFaultBox out of level, or uneven fabric thicknessLevel the box
Small ripples hugging the zipper weldFaultZip welded too hotWarranty claim
Fabric overlapping itself on the rollFault (ITRS)Excess fabric folding over as it windsStop and call the installer

The normal rows come from the ITRS, the German trade association for technical textiles and sun protection, and its guideline for assessing made-up shade fabrics (December 2016), drafted with other European makers' and weavers' associations. The fault rows come from the troubleshooting tables in Rollease Acmeda's Zipscreen installation manual (v4.4, March 2020) and Isotra's Screen HR10-ZIP manual. If the edge comes out of its channel rather than wrinkling in it, see screen off track.

Why the edges wrinkle on a screen with nothing wrong

A zip screen has a zipper strip welded along each fabric edge, running in a retention channel inside each side track (edge designs are compared in zip track, keder and zipper edges). The zip lies on top of the fabric, so the roll is thicker at its ends than in the middle. In the ITRS guideline's words (our translation from German), zip-guided fabrics "show slight wrinkles especially at the edge," because fabric and zipper "lie on top of each other and travel different distances when winding." Weather makes it worse.

The guideline puts a number on the same effect at a doubled seam: with fabric about 0.5 mm thick, the two layers differ by 3.14 mm per turn of the tube.

Worked example: An 8 ft (2.44 m) drop of 0.5 mm fabric (the thickness Dickson lists for its SWK Zip) on the 78 mm tube in Rollease Acmeda's charts winds to a roll of about 87 mm in about nine turns. If the zip adds just one fabric thickness at the edge, at 3.14 mm per turn the edge ends up at least 28 mm (about 1-1/8 in) out of step with the middle by the time the screen is up. That length has to go somewhere, and it goes into edge ripples.

Rollease Acmeda's manual says the same from the installer's side. For "ripples along sides of fabric" after a long time rolled up, the effect "is inherent to roller systems and is more prevalent in some fabrics. Leave blind down for 1-4 hours, most ripples should disappear." Ripples are "more common" on spring-operated blinds; pulling the blind down softly before locking it reduces them.

The ITRS also shows gathering at horizontal seams and crosswise imprints from the tube attachment as allowable, with no effect on the fabric's quality, function or lifespan.

Diagonal creases: check level and square

Isotra's HR10-ZIP manual ties diagonal creases to installation geometry: if box and guide rails are not fitted correctly, "the bottom lath may roll up askew into the box and the screen cloth will have diagonal or crosswise creases." Its entry for "folds and waves in the fabric" gives one cause, box or guide rail not level.

Front view of a zip screen with the head box across the top, a side channel down each side, three width measurements W1, W2 and W3 between the channels and two corner-to-corner diagonals D1 and D2
Measure the inside width between the channels just under the box (W1), at mid height (W2) and at the bottom (W3), then both diagonals (D1 and D2). Isotra's limit is 2 mm (about 5/64 in): the three widths must agree within 2 mm, and so must the two diagonals.
  1. Level the head box. Put the level on the box, not the ceiling. Isotra says to check the whole assembly is "dead level" first, and Rollease Acmeda traces a bottom bar that looks uneven to a box that is not level.
  2. Measure the three widths. Measure to the millimeter, starting "directly under the box." Over 2 mm, Isotra warns, "the fabric may not hang sufficiently taut."
  3. Measure both diagonals. Isotra's Screen ZIP manual requires the widths or the diagonals to "be the same ±2 mm." Equal widths with unequal diagonals mean parallel channels that are not square to the box.
  4. Correct and recheck. Shim behind channels and box until the numbers agree. Rollease Acmeda packs the opening until its widest point is within 10 mm of the narrowest before mounting. Cycle the screen and measure again.

Fixings and packing are covered in installing motorized patio screens, and channel profiles in screen tracks and guide rails.

Waves everywhere: slack fabric

Isotra's list for "fabric tension is too slack" includes a bottom lath resting on the sill instead of hanging from the fabric, a lower end limit set "too low or too loosely," a zipper out of its guide profile, and fabric that is too wide. Rollease Acmeda adds a weight bar that is too light (add ballast) and, on spring blinds, too few spring pre-turns.

The two manuals seem to disagree on the bottom limit. Rollease Acmeda sets it "to the lowest point possible" with the seal "compressed as much as possible"; Isotra warns that a bar resting on the sill leaves the fabric slack. Both hold if the bar stops where its seal is compressed, before the sill takes the bar's weight. Re-setting follows the motor maker's procedure (see limit settings).

For width, Rollease Acmeda's check is that the fabric from outer zip edge to outer zip edge equals the finished blind width minus 66 mm. That deduction is for its Zipscreen only; a panel made too wide for its channels has to wrinkle somewhere.

A smile, or fabric creeping sideways

A smile is a sag across the panel, lowest in the middle. Rollease Acmeda gives two causes: "not enough tension in side guides," fixed with a new fabric skin and the zip re-welded "ensuring temperature is not too hot," and fabric not installed straight on tube and weight bar. The tube adds to it. The ITRS guideline takes tube deflection as generally 0.1-0.3% of length, or 4-12 mm (about 3/16-1/2 in) at the center of a 13 ft (4 m) screen. Crestron's shade fabric guide, written for indoor roller shades, says "the wider the shade and the heavier the fabric, the more deflection tends to occur." Wide screens need bigger tubes and deeper housings for that reason (see motorized screen housing sizes).

Fabric creeping toward one end of the tube is telescoping. Crestron names "the levelness of the mounting surface" as the most common cause. Isotra adds uneven fabric thickness, a fabric manufacturing defect, and fixes it with layers of adhesive tape on the tube on the side opposite to where the fabric moves.

Faults that need a new fabric panel

Rollease Acmeda puts "small ripples close to weld" down to welding temperature too high, with a new fabric skin as the fix, the same fix as for fabric "permanently damaged due to inadequate handling." The ITRS draws a line on the roll too: waves are allowable, but fabric overlapping itself with pronounced overwind folds is "not allowable."

Fabric choice changes how much rippling you see. Serge Ferrari says its Soltis Veozip polyester adapts "without deformation or wrinkling of the fabric caused by frequent use or excessive tension in the zip rails," and that fiberglass screen fabric "leaves marks when folded." The ITRS says stiff PVC-coated fabrics, at up to about 500 g per square meter, tend to fold as they wind. Hardware matters too: Eclipse's E-Zip brochure credits its spring-clip tracks with operation "without any side fabric wrinkles" and uses "the largest roller tube possible" for "a smooth flat fabric." Solar fabric thickness and weight are compared in Textilene vs SunTex.

Do not roll it up wet: The ITRS guideline says fabric rolled up wet sets its waves and wrinkles "to a particular degree" and can mildew between layers. Lower it again at the first dry spell. Cleaning without leaving it damp is in how to clean retractable and solar screens.

Where this stops applying

  • No published millimeter limit for wrinkle size. The ITRS photos carry scale bars, but the guideline says they are only reference points and the maximum size of a fault cannot be read from them.
  • The ITRS guideline is European and has no force in a U.S. warranty claim, which is settled by the maker's own terms.
  • The 2 mm and 66 mm figures are Isotra's and Rollease Acmeda's. Use your own screen's manual where you have it.
  • Ripples only in wind are load on the channels; see zip track screens and wind resistance.

Bottom line

Edge ripples that fade within 1-4 hours down are normal. Wrinkles that stay are measurable: widths and diagonals within 2 mm, box level, bottom bar hanging free of the sill. Ripples at the weld or fabric overlapping on the roll need a new panel from the installer or maker.

Frequently asked questions

Will the wrinkles in my new zip screen go away?

Edge ripples from shipping or a long time rolled up usually do; Rollease Acmeda expects most to go within 1-4 hours down.

Are zip screen wrinkles covered by warranty?

Fabrication faults such as an overheated weld or a panel cut too wide are the maker's problem. The European guideline classes light edge ripples as allowable, so expect a maker to treat those as normal. Check your warranty wording.

Can I heat out the wrinkles?

None of the manuals we read recommends heat on zip fabric, and Rollease Acmeda's weld fault comes from too much heat. Use time down, then correct the installation.

Sources and standards consulted

  • Tubular motor troubleshooting, limit-setting and remote pairing guides (manufacturer documentation)
  • Lateral arm awning service manuals (pitch, arm and spring adjustment) (manufacturer documentation)
  • Retractable screen manufacturer service and re-tensioning instructions (manufacturer documentation)

See how we research for our sourcing and verification process.