Pleated screen door sagging, dragging or not closing square: how to adjust the cords

Tighten the cords if they hang loose in the doorway. Loosen them if the screen has gone stiff. Stop at the point where there is no slack and only slight tension. Genius tells installers to push the cord tensioner along "until there is slight tension. There should no longer be any slack in the cords." Its ZigZag sheet adds the other half: "never make the cords tight," because too much tension "will cause the screen to operate poorly and can damage the cords." Before you touch the tension, check for a snagged cord and a dirty track. Then move the tensioners in small, equal steps.

Key takeaways

  • The target is no slack and slight tension, in Genius's words. Tight is too far. Streme's test is a bar that runs smoothly.
  • Sagging cords mean too little tension, or one cord longer than the rest. A stiff screen can mean too much tension, but check the tracks and look for trapped cords first.
  • Genius says to adjust "only if needed," in equal steps, and with both tensioners. Set the tension with the screen fully open, as the ZigZag1 sheet does.
  • One cord looser than the others is fixed at the knot, not at the tensioner. Genius gives the steps for its ZigZag1 and ZigZag2.
  • A broken cord means a restring kit or a new panel from the maker. None of the sheets we read gives restringing steps.

What the cords on a pleated screen door do

A pleated screen door has mesh folded like an accordion. It slides between a top guide and a low bottom guide, and you push and pull it by hand. There is no spring. Thin cords run through the folds, from the frame at one side to the handle bar at the other. They guide the folds as the screen opens and closes. Nothing stores energy, so the screen stays where you leave it. That is the main way it differs from a roll-up door (see pleated vs roll-up retractable screen doors).

The cord tensioner is the small part that holds the cord ends and sets how much slack they have. Makers name it differently. Genius calls it a Cord Lock Tensioner or Cord Tensioner, Streme calls it a "tuner," and Isotra calls it an "adjusting element." Cord tension is how taut the cords are once that part is locked. More tension pulls the slack out of the cords. Less lets them hang. The layout of the moving parts is in how retractable screens retract.

Tighter or looser? Why both answers go around

Both answers are right for one symptom and wrong for the other. The "tighten it" advice comes from sagging. Genius's troubleshooting table for the ZigZag1 (distributed by JELD-WEN) and the ZigZag2 gives one fix when "the cords sag into the opening when operating the Screen": "Try increasing the tension on the corresponding cord tensioner." Sagging is easy to see, so that half of the advice spreads.

The other half is in the Genius ZigZag sheet: the cords "should not be over tensioned or made tight." Too much tension makes the screen "operate poorly," and it "can damage the cords."

So the rule is no slack, slight tension, and nothing past that. Streme gives the test. Push the handle bar to the closed position, and "if it runs smoothly then the string tension is correct." If tightening a sagging cord makes the whole screen stiff, stop. The tension is not the problem. One cord is longer than the others, and that has its own fix (below).

Symptom table: what you see and what to change

Pleated screen door faults and fixes (sources: Genius ZigZag1, ZigZag2 and ZigZag sheets; Streme single pleated, Feb 2025; Isotra PS1)
What you seeMost likely causeWhat to do
Cords hang down into the doorway as you close itToo little tension, or one cord longer than the restAdd tension at that side's tensioner. If one cord still hangs, fix its length at the knot
One cord is visibly looser than the othersUneven cord lengthLoosen the tensioner, untie the knot, take up the slack, retie
Screen is stiff or rough to slideDirty tracks, a cord trapped in an end plug, or cords too tightClean and silicone the guides, free the cords, then back the tension off evenly
Screen will not close all the wayA snagged or pinched cordCheck the cords at the top and bottom of the cassette and at the top guide notch
Handle bar meets the side at one end but not the otherFrame out of square, or the tensioners set unevenlyCheck the frame first, then set both tensioners again, together
Gap between the two bars of a double screenCenter cord carriers apart or off center, or one cord looseButt the carriers at the center mark, in line with the floor stop block
Tensioner will not slideSide guide track needs lubricatingSilicone spray inside the side guides
A cord has snappedWear or over-tensionRestring kit or new panel from the maker

Where the tensioners are on each screen

The parts differ, but each sheet has a way to set the top cords and the bottom cords. Here is where to look on the screens whose sheets we read.

Cord tensioners by maker, as described in each installation sheet
ScreenThe maker's name for itWhere it sitsHow it locks
Genius ZigZag1 (JELD-WEN, 08/19)Cord Lock Tensioner, upper and lowerBehind the magnet strip on the magnet profileHex screws, 2 mm Allen wrench supplied
Genius ZigZag2 double panelCord Tensioner, plus a Cord Carrier at the centerInside the top guide, next to each cassette. Bottom cord knots sit in the slot of the Stop Block at the floor centerTwo set screws facing down, 2 mm Allen wrench supplied
Streme single pleated (UK, Feb 2025)Square plastic "tuner," one for each set of stringsIn the top corner and the bottom corner, with the small screw head showingTurn the screw left or right with the screwdriver in the fixing pack
Isotra PS1 / PS1 V (12/2023)Upper and lower adjusting elementNot described beyond "upper" and "lower"Not stated; the element is shifted to set the tension

On the ZigZag2, pushing the cord tensioner toward its cassette takes up slack. The ZigZag2 sheet also notes that "the number and color of cords may vary," so count your own cords rather than trusting a photo.

Check these before you change the tension

Each of these is in at least one maker's troubleshooting steps. Rule them out first.

  1. Snags and pinched cords. Genius says to ensure "there are no snags, tangles, or pinched cords," especially at the top and bottom of the cassette and in the notch and track of the top guide.
  2. Cords running freely. Streme's test: hold one set of strings in one hand and pull the handle bar a little toward the middle with the other. "The strings will move if they are free." If they do not, ease the bar out of the tracks and look at the top and bottom end plugs for a trapped string.
  3. Clean tracks. Streme says to vacuum the bottom track often and wipe it with a damp cloth, which "will ensure the continued smooth running of your screen."
  4. Silicone in the guides. Genius says to spray silicone inside the top and bottom guides "to improve sliding," and Streme says the same for its tracks. If a ZigZag1 tensioner is hard to slide, its sheet says to spray the track inside the side guides. The sheets name guides and tracks, never the cords.

How to adjust the cord tension

These steps combine the Genius ZigZag1, ZigZag2 and ZigZag sheets with the Streme and Isotra sheets. Where one maker adds a step, it is named.

  1. Open the screen fully. The ZigZag1 sheet sets tension "ensuring the screen is fully collapsed," and says to fully collapse it again before any readjustment.
  2. Get to the tensioners. On a ZigZag1, pull out the magnet strip. On a ZigZag2, they are in the top guide. On a Streme, they are in the corners.
  3. Loosen the lock. Use the 2 mm Allen wrench on a Genius. On a Streme, the screw itself is the adjustment.
  4. Move it a little. Take up slack until there is slight tension and no slack. Move the top and bottom tensioners in even steps. Streme suggests changing the top strings first, testing, and only then changing the bottom strings.
  5. Lock it and test. Tighten the set screws. Then open and close the screen several times, as Isotra says, and fine-tune if needed.
  6. Put the cover back. On a ZigZag1, push the magnet strip back into the groove.

If the screen still runs badly, look at the cord lengths before adding more tension.

One cord longer than the rest: fix it at the knot

Tension cannot fix a cord that is longer than its neighbors. The tensioner pulls the whole set, so the short cords go tight while the long one still hangs. Genius's ZigZag1 and ZigZag2 tables both send you to the knot instead.

  1. Loosen the tensioner screws on the side with the uneven cords.
  2. Untie the knot. On a ZigZag2, first pull the knotted end out of the Stop Block slot. Its sheet says to cut the knot off.
  3. Pull the slack out of the long cord until all the cords are the same length.
  4. Retie the knot. The ZigZag2 sheet says to use a square knot and trim the extra, but "be sure not to trim more than 6''."
  5. Seat the knot again and re-tension the cords as above.
Worked example: Take a Genius ZigZag2 double screen on a wide slider. Suppose the cords of the left panel droop into the doorway as it closes, and the right panel is fine. Start with the checks. Say there is no snag at the cassette and none in the top guide notch. Open the left panel fully. Loosen the two set screws on the left cord tensioner with the 2 mm Allen wrench. Push the tensioner toward the left cassette until the slack is gone and the cords are just taut. Lock both screws and run the panel a few times.

Now suppose one cord still hangs while the rest are taut. More tension would only tighten the good cords, so the fix moves to the knot, as in the steps above.

Last, check the center. If a gap shows where the two pull bars meet, the ZigZag2 sheet says the two Cord Carriers should be "butted tight together" at the center of the top guide. They should also sit right above the Stop Block on the floor. If they are off, loosen all the top adjustments and line them up.

Not closing square: the frame first, then the cords

A handle bar that meets the side at the top but not the bottom, or the other way round, usually points to the frame or to uneven tensioners. Start with the frame. Measure the two diagonals of the opening and compare them; no sheet we read gives a tolerance. Streme says its screen "must be fitted square to ensure it functions correctly," and if the opening is not, to "pack out" (shim) the side profiles and top track rather than the bottom track. Isotra supplies a plastic part with a spring for its PS1 and recommends it "in doors that are not right-angled." It goes in the guide rail and "must be slightly flexible."

Then check the tensioners. Genius says to adjust "uniformly using both" tensioners. If someone has moved only one, loosen both and set them again together. Then look for a pinched cord. Genius lists snags at the top and bottom of the cassette as a cause when "one of the screens doesn't close all the way."

When a cord breaks

A snapped cord cannot be tensioned. The fix is replacement parts from the maker: a restring kit if it sells one, or a new screen panel. The Genius sheets print a phone number for replacement parts. None of the installation sheets we read gives restring steps, so we do not give any here. On a Genius screen, the ZigZag1 sheet says a warranty claim needs the registration number and proof of purchase. What lifetime warranties usually cover is in retractable screen warranties. Other faults on both screen types are in retractable screen repair.

Where this stops applying

The steps come from the sheets of three makers: Genius (ZigZag, ZigZag1, ZigZag2), Streme and Isotra. Other pleated screens may lock their cords with a different part, so check your own sheet before you loosen anything. The knot fix is Genius's; the Streme and Isotra sheets do not give one. A roll-up door works on a spring, not cords, so none of this applies to it (a roll-up that races back in is covered in why a retractable screen door slams shut). Mesh pushed out of its track in wind is not a cord fault either. Streme supplies "windproof clips" for screens over 1,300 mm (about 51 in) wide, and re-seating a screen is covered in retractable screen off track. Finally, no sheet gives a force or a number of turns for "slight tension." The test is whether the screen runs smoothly with no cord hanging loose.

Bottom line

Check for snags, trapped cords and dirty tracks first. Then open the screen fully and move both tensioners in small, equal steps until the cords have no slack and only slight tension. If one cord still hangs while the others are taut, fix that cord at the knot instead of adding tension. Never make the cords tight. A broken cord means a kit or panel from the maker.

Sources

Frequently asked questions

How tight should the cords on a pleated screen door be?

Just taut. Genius says "slight tension" with no slack, and never tight. Streme's test is that the bar runs smoothly when you push it closed. If you have to tighten until the screen is stiff to stop a cord sagging, that cord is too long.

Why is my pleated screen harder to slide since I tightened the cords?

Too much tension. Back both tensioners off in equal steps until the screen runs smoothly with no cord hanging.

Should I spray silicone on the cords?

No sheet we read says to. Genius and Streme say to spray inside the guides and tracks.

Sources and standards consulted

  • Tubular motor troubleshooting, limit-setting and remote pairing guides (manufacturer documentation)
  • Lateral arm awning service manuals (pitch, arm and spring adjustment) (manufacturer documentation)
  • Retractable screen manufacturer service and re-tensioning instructions (manufacturer documentation)

See how we research for our sourcing and verification process.