Is a Retractable Screen Door Wheelchair Accessible? Track Height, Width and Pull Force
It can be, but only as fitted to your doorway. No screen is accessible on its own, because the ADA rules check the doorway, not the product. A retractable screen door passes when three numbers pass with it in place. The bottom track, plus any sill under it, is no more than 1/2 in (13 mm) high. The opening left beside the parked screen is at least 32 in (815 mm) wide. And it takes no more than 5 lb (22.2 N) of force to open. A low pleated track clears the height rule easily: Streme's is 4 mm. Width is where screens fail. In a 36 in opening, a pleated screen fitted inside the frame leaves less than 32 in.
Key takeaways
- Height: the ADA allows a threshold up to 1/2 in (13 mm). Up to 1/4 in (6.4 mm) may be a square edge; from 1/4 to 1/2 in it must be beveled. Over 1/2 in needs a ramp.
- Count the house sill too. A 4 mm track glued on top of a 3/8 in sill makes a step of about 13.5 mm, just over the limit.
- Width: 32 in (815 mm) clear, measured with the screen fully parked. Nothing may stick into that width below 34 in (865 mm).
- In a 36 in opening, Streme's inside-fitted pleated screen leaves about 30-7/8 in (784 mm). A 1-7/8 in roll-up housing leaves 34-1/8 in before the pull bar.
- Force: 5 lb (22.2 N) for sliding or folding doors. No screen maker sheet we read gives a measured opening force, so you have to measure it.
What "ADA accessible" means for a screen door
The ADA Standards are the 2010 design rules issued under the Americans with Disabilities Act. The Access Board's online copy says they apply to "places of public accommodation, commercial facilities, and state and local government facilities." Most private homes are not covered. Section 404 of the standards covers doors and doorways, and three of its rules decide whether a screen door works for a wheelchair.
- Threshold. A threshold is the raised strip at the foot of a doorway. For a retractable screen it is the bottom track, plus whatever sill the track sits on. Rule 404.2.5 caps it at 1/2 in (13 mm).
- Change in level. This is any step up or down in the floor. Rules 303.2 to 303.4 say how it may be shaped. A bevel is a sloped edge. A slope of 1:2 rises 1 in for every 2 in across.
- Clear width. This is the open space a wheelchair rolls through. Rule 404.2.3 sets 32 in (815 mm) as the minimum.
- Opening force. This is the steady push or pull it takes to open the door all the way. Rule 404.2.9 sets 5 lb (22.2 N) for sliding or folding doors.
The ADA does not name screen doors. A roll-up screen slides across the opening and a pleated screen folds, so we read them against the sliding and folding door rules. How the two types work is set out in pleated vs roll-up retractable screen doors.
Bottom track height: the 1/2 inch rule
Rule 404.2.5 says a threshold "shall be 1/2 inch (13 mm) high maximum." The rules on changes in level then set its shape:
- Up to 1/4 in (6.4 mm): may be vertical, a plain square edge (303.2).
- 1/4 to 1/2 in (6.4 to 13 mm): must be beveled, no steeper than 1:2 (303.3). The standard allows 1/4 in vertical plus 1/4 in beveled, as long as the total stays at 1/2 in or less.
- Over 1/2 in (13 mm): must be ramped (303.4).
One exception: an existing or altered threshold may be up to 3/4 in (19 mm) high if it is beveled on each side, no steeper than 1:2.
Most retractable screen sheets do not print a track height at all. The table shows what the documents we read do say.
| Screen | Type | What the document says about the bottom track | Against the ADA rule |
|---|---|---|---|
| Streme single pleated door, reveal fitted | Pleated | "The bottom track at 4mm deep adheres to the floor" | 4 mm is under 6.4 mm, so a square edge is allowed, on a flat floor |
| Genius Sheer Classic | Pleated | "ADA Compliant"; an "Alternate Sloped Sill Bottom Guide" is offered; no height given | Cannot be checked from the page; measure it |
| Brisa single (Larson instructions 202221004-0123) | Roll-up kit | A sill plate with extenders slides onto the bottom track and is screwed to the sill; no height given | Cannot be checked from the sheet; measure it |
| Phantom door screen | Roll-up, custom | Aluminum track; "various threshold adaptors" listed for its oversized screen; no height given | Cannot be checked from the catalogue; measure it |
Measure from the floor on each side to the top of the track. The screen track does not replace the door sill. It sits on it. The Brisa sheet sorts sills into three types: flush with the exterior trim, short of it, or extended past it. On an extended sill "the assembly rests on top of the sill." On a short sill over a step, Brisa calls for a filler board under the trim, cut so its top is even with the sill. That filler board supports the screen. It does nothing for the step a wheelchair has to cross.
So the number that counts is the total height. Suppose a doorway has a 3/8 in (9.5 mm) beveled sill, and a 4 mm pleated track is glued on top. The peak is now about 13.5 mm, a little over the 13 mm limit. The same track on a flat floor passes with room to spare. More on track profiles and low-threshold tracks is in screen tracks and guide rails.
Clear width: 32 inches with the screen parked
Rule 404.2.3 asks for "a clear width of 32 inches (815 mm) minimum." For a swinging door, the ADA measures it between the face of the door and the stop, with the door open 90 degrees. It adds: "There shall be no projections into the required clear opening width lower than 34 inches (865 mm)." Between 34 and 80 in up, a projection may stick in no more than 4 in (100 mm).
A retractable screen has no swing, so we measure it the way the rule treats a door: fully open. Pull the screen all the way back. Then measure from the face of the parked screen to the nearest part on the latch side. On a roll-up that is the pull bar and its handle at one end, and the latch strip at the other. On a pleated screen it is the folded stack of mesh. These parts run from the floor up, so they all fall in the zone below 34 in where nothing may stick in.
The house door counts too. The screen sits in front of or behind a swinging door, and that door has its own clear width when open. Whichever is narrower, the door or the screen, is the clear width of the doorway. A screen cannot make a narrow door wider.
Worked case: a 36 inch doorway, two screens
A pleated screen fitted inside the opening. Streme's measuring guide gives the parked stack for a reveal-fitted screen up to 1,000 mm wide as 105 mm. That stack is "the side channel, mesh and handle bar when the screen is open." The closing channel on the other side is 25 mm wide. So 914 - 105 - 25 = 784 mm, or about 30-7/8 in. That is 31 mm (about 1-1/4 in) short of 815 mm. Worked back, the same screen needs an opening of at least 945 mm (about 37-1/4 in) to leave 32 in clear.
A roll-up screen mounted in the jamb. Phantom's door screen housing is 1-7/8 in (48 mm) wide. Set inside the opening, it leaves 36 - 1-7/8 = 34-1/8 in (867 mm). The pull bar parks beside the housing, and a latch strip goes on the far jamb. Phantom lists both parts but does not give their widths. So the bar and the latch side together can take up to 2-1/8 in (52 mm) before the opening drops under 32 in. Measure them on the screen you are quoted.
A surface-mounted kit. The Brisa kit fits 32 to 36 in openings. Its housings screw to the trim face, with the flanges "snug to the edges of the door jamb," so the housing itself sits outside the opening. Where the slider bar parks is not stated. Here too, measure with the screen fully open.
On these figures, the roll-up can leave 32 in in a 36 in doorway, and the inside-fitted pleated screen cannot.
Pleated screens are often sold as the accessible choice, for the flat track and no spring. On height they win. On width, the stack is the price, and it grows with screen width (Streme's full table is in the pleated vs roll-up comparison). For other widths and kit fit ranges, see retractable screen door sizes. A doorway that is 32 in to begin with has nothing to spare for any screen mounted inside it.
Pull force: the 5 pound rule
Rule 404.2.9 sets the force to push or pull open "sliding or folding doors" at "5 pounds (22.2 N) maximum." The ADA's note on the rule says this is "the continuous application of force necessary to fully open a door." It is "not the initial force needed to overcome the inertia of the door." It also does not include the force to release a latch.
The handle has its own rules. Under 404.2.7, handles, pulls and latches must work with one hand, without "tight grasping, pinching, or twisting of the wrist" (309.4). They must sit 34 to 48 in (865 to 1,220 mm) above the floor. And "where sliding doors are in the fully open position, operating hardware shall be exposed and usable from both sides." On a roll-up, that means the pull bar's handle must still be reachable from inside and outside once the screen is parked. Phantom lists an outside and an inside handle, and the Brisa kit has a handle on each side.
The two types load the hand in different ways. A roll-up's spring pulls the screen back toward the housing, so the spring helps when you open the doorway and works against you when you pull the screen across. How much it pulls is set by preload, explained in retractable screen spring tension. A pleated screen has no spring, so you move it both ways yourself, against the cords and the guides.
No screen maker sheet we read gives a measured opening force. That includes the Genius page that calls the Sheer Classic "ADA Compliant." So check it yourself. Hook a luggage scale or a push-pull gauge on the handle. Move the screen through its full travel at a steady walking pace. Read the force while it is moving, not the jump at the start. Do it in both directions. Clean the track first: Brisa's FAQ lists dirt in the tracks as a cause of slow travel. If it reads over 5 lb, the track or the tension needs work before the door counts as accessible.
The three checks, side by side
| Check | ADA limit | How to measure on a screen | Where screens fall short |
|---|---|---|---|
| Threshold height (404.2.5, 303) | 1/2 in (13 mm) max; square edge to 1/4 in, beveled 1:2 above; existing or altered 3/4 in (19 mm) if beveled both sides | Floor on each side to the top of the track, sill included | A low track on a raised sill; most sheets give no track height |
| Clear width (404.2.3) | 32 in (815 mm) min; no projection below 34 in | Screen fully parked, face of stack or pull bar to latch side | Pleated stacks fitted inside narrow openings |
| Opening force (404.2.9) | 5 lb (22.2 N) max, continuous, latch release excluded | Scale on the handle, steady pull, full travel, both ways | No maker figure to rely on |
| Hardware (404.2.7, 309.4) | One hand, no tight grip or twist; 34 to 48 in high; usable from both sides when fully open | Handle height and reach with the screen parked | A handle not reachable from both sides once the screen is parked |
Before you order, the basics of mounting and frame checks are in retractable screen doors, and the three-point measuring method is in how to measure for retractable screens. On a patio slider, the screen covers only the vent panel, which is often the narrowest part of the opening; see screens for sliding glass doors.
What this does not cover
The ADA Standards govern public accommodations, commercial facilities and state and local government buildings, in new work, alterations and additions. They do not govern most private homes. Where a business runs from a home, the Justice Department rule printed with the standards says the part "used exclusively as a residence is not covered," while the business part and the way into it are. At home, these numbers are a useful yardstick, not a legal test. In a shop or office, the screen is one part of a doorway that also needs clear floor space to approach the door, which this page does not cover. No screen maker sheet we read claims a tested ADA opening force, and the one "ADA Compliant" claim we found gives no figures behind it. A screen that meets all three numbers is still not a code sign-off. Your local building official, or the person responsible for the building's access plan, makes that call. The figures here are for the products named and change as product lines change.
Bottom line
A retractable screen door can be wheelchair accessible if the doorway passes three checks with the screen fitted: no more than 1/2 in from floor to track top, sill included; 32 in clear with the screen fully parked; and 5 lb or less to open. Pleated screens win on track height, with a 4 mm track on a flat floor. In a 36 in opening, a pleated stack fitted inside the frame leaves only about 30-7/8 in, while a 1-7/8 in roll-up housing leaves room for 32 in. No maker publishes a force figure, so measure it yourself.
Sources
- U.S. Access Board, 2010 ADA Standards for Accessible Design (online edition): 303.2 to 303.4, 309.4, 404.2.3, 404.2.5, 404.2.7, 404.2.9 and Advisory 404.2.9, plus the scope statement and the Department of Justice rule on commercial facilities in private residences.
- Streme, How to measure: single pleated door screens (bottom track, closing channel and stack widths).
- Metro Screenworks, Genius Sheer Classic 5-Panel Retractable Screen ("ADA Compliant" claim and bottom guide option).
- Larson, Single Panel Retractable Door owner's guide and installation instructions, 202221004-0123 (32 to 36 in fit, sill types, sill plate, filler board).
- Phantom Screens, Product Catalogue, February 2024 (door screen housing 1-7/8 x 2-49/64 in, handles, mounting options).
Frequently asked questions
Are retractable screen doors ADA compliant?
Not as a product. The ADA checks the finished doorway. A screen helps it pass if the track and sill together stay at 1/2 in or less, the parked screen leaves 32 in clear, and it opens with 5 lb or less.
Can a wheelchair roll over a retractable screen track?
A track up to 1/4 in (6.4 mm) high may have a square edge under the ADA rules. Streme's 4 mm pleated track is under that on a flat floor. Between 1/4 and 1/2 in the edge must be beveled, and above 1/2 in you need a ramp.
Does a retractable screen make my doorway narrower?
If it is mounted inside the opening, yes. The parked housing, pull bar or pleat stack takes width. Streme's inside-fitted pleated stack is 105 mm on a screen up to 1,000 mm wide, plus a 25 mm closing channel. Surface-mounted kits screw to the trim instead.
Do the ADA rules apply to a screen door at my house?
Not in most private homes. The 2010 ADA Standards apply to public accommodations, commercial facilities and state and local government buildings. The part of a home used for a business is covered. The rest of the home is not.
Sources and standards consulted
- EN 13561:2015, External blinds and awnings (covers vertical external screens and wind classes) (CEN)
- Screen mesh specification sheets (fiberglass, polyester and PVC-coated meshes) (manufacturer documentation)
- Energy Efficient Window Attachments (U.S. Department of Energy, Energy Saver)
- Attachments Energy Rating Council (AERC) rating program (AERC)
See how we research for our sourcing and verification process.