Why won't my Pella Rolscreen retract, and how do you re-tension it?
A Pella Rolscreen that will not roll back up has either screen cloth out of one of its side guides or a roller spring that has lost its tension. Check the cloth first, because Pella's fix for that takes a minute and no tools. If the spring is the problem, take the screen out of the window and wind the slotted end of the roller with a flat blade screwdriver, in the direction of the arrows. Pella's service instruction for Rolscreens made from February 2017 on gives the count: 11 full turns if the window frame is 20-3/4 in (527 mm) wide or less, 27 turns if it is wider. Then back the screwdriver off a little until it catches. Never spray a lubricant on it. Pella warns that operating the screen can cause a static discharge, and near an aerosol lubricant that spark "could cause ignition."
Key takeaways
- Cloth out of a guide: push the cloth to the outside, raise the bar to the top, then lower it. Pella says the cloth goes back into the guide by itself.
- Full re-tension from slack: 11 turns for frames 20-3/4 in wide or less, 27 turns for wider frames. Count full turns of the screwdriver.
- After the last turn, back off slightly until you feel resistance. If it resists at once, stop. Pella says forcing it can damage the tensioner.
- Pella's 2016 care sheet adds a small top-up: a gear on the left end that clicks, 8 clicks to one turn, with the screen down and only the head cover off.
- No aerosol sprays, dry silicone included. Pella says to use no flammable substance on a retractable screen at all.
What a Rolscreen is, and what "re-tension" means
Rolscreen is Pella's name for its retractable window screen. It mounts inside the room, at the head of the window. Pella's owner's manual lists it under casement and awning windows in its Reserve, Architect Series and Lifestyle Series lines. The manual says the screen "is designed to retract when not in use," and that it "features spring action and will spring to the top if released."
Pella calls the whole unit the cartridge. Its 2017-on service instruction lists the parts: a head cover on the room side, a screen roll, a back cover and two end caps, one left and one right, that double as mounting brackets. The end caps screw to the window frame. A side guide on each jamb holds the edges of the cloth. At the bottom of the cloth is the operator bar, which you pull down and latch at the sill.
The screen roll has a spring inside. Pulling the bar down winds the spring tighter, and unlatching it lets the spring roll the cloth back up. Re-tensioning means winding turns back into that spring after its tension has been released, which is the case Pella's 11 and 27 turn figures are written for. How a roller spring builds its pull is explained in our retractable screen spring tension guide.
Pella also makes an Integrated Rolscreen, launched in 2018 for double-hung and single-hung windows. That screen is built into the window frame, appears when you raise the sash and uses magnets to stay connected. It is a different product, and nothing on this page applies to it.
First check: is the cloth out of a guide?
Look at both side edges of the cloth with the screen partway down. An edge that has slipped out of its guide channel is easy to see from inside the room.
Pella's owner's manual gives the fix in one line: "gently push the screen cloth out to the exterior, raise the operator bar to the top of the window, and lower the screen. The screen cloth will retract back into the guide." Raise the bar with both hands, as Pella says to for normal use. If the cloth keeps leaving the same guide, the guide may have shifted. The guide checks in step 9 below are the ones Pella calls "critical." Other brands' cloth-out-of-track problems are covered in retractable screen off track.
Some pull or no pull: which spring fix you need
If the cloth sits in both guides, the spring is next. Unlatch the bar and hold it, then let it rise slowly with your hands on it. You are feeling for how hard the spring pulls up.
| What you see | What it points to | Pella's fix |
|---|---|---|
| One edge of the cloth outside its guide | Cloth disengaged from the guide | Push the cloth to the outside, raise the bar to the top, lower the screen |
| The spring still pulls up, but the bar stops short of the top | Spring low on tension | A small top-up on the click gear, if your cartridge has one (81VS0100, Option 1); otherwise the full re-tension |
| No upward pull at all; the bar just hangs | Spring tension released | Take the cartridge out and wind 11 or 27 full turns (81XJ0000; 81VS0100, Option 2) |
| The screwdriver resists at once when you back it off | The tensioner is already holding | Do not force it back any further |
Rule out friction before you add tension. Our spring tension symptoms table explains why: a screen dragging on dirt stops short however the spring is set, and extra turns only move the strain to the latch and the spring.
A small top-up: the click gear
Pella's 2016 installation, operation and care sheet (part number 81VS0100) gives two ways to adjust roller tension. It calls Option 1 "typically used for minor tension adjustments," and it does not need the cartridge out of the window.
- Lower the screen and latch it. Pella says the screen must be in the lowered, closed position.
- Take off the head cover. Hold the cover with one hand near each end, pull the bottom of it out, then lift it up and off.
- Push the gear on the left side of the cartridge with a flat blade screwdriver. Each click adds 1/8 of a turn of tension, so 8 clicks make one full turn.
- Put the head cover back. Hook it over the cartridge with the cover slot on the end cap tab, rotate the bottom down and press near the ends until it clicks in.
Pella gives no click count for a top-up. It says only that the number of turns "will vary" with the width of the unit. Our spring tension guide gives the general method: add a turn at a time (8 clicks here), then test from halfway down. Stop as soon as the bar returns to the top on its own.
The 2017-on service instruction does not mention this click gear. If your cartridge has no gear on the left that clicks when pushed, use the full re-tension below.
Full re-tension: Pella's steps for Rolscreens made 2/2017 on
These steps come from Pella's Rolscreen cartridge service instruction, part number 81XJ0000, rev. 10/17/2016. It covers the "Rolscreen Retractable Screen 2/2017-Current." Pella's 2016 care sheet gives the same turn counts as its Option 2, "typically used when all the tension on the spring has been released." You need a flat blade screwdriver and a drill/driver with a #1 square drive bit.
- Raise the screen all the way. Pella starts with the screen fully raised.
- Take out the guide screws. The number of screws depends on the height of the window.
- Remove each guide. Pull it toward the center of the window, then down, to free it from the end cap. Repeat on the other side.
- Remove the cartridge screw from each end cap. Hold the cartridge while you do this, so it does not fall out of the window. Set it on a smooth, flat surface.
- Find the slotted end of the screen assembly. Look for the arrows that show which way to turn.
- Wind the spring with the flat blade screwdriver, in the direction of the arrows. Count full turns: 11 for a frame 20-3/4 in (527 mm) wide or less, 27 for a wider frame.
- Back off slightly. After the last turn, turn the screwdriver back a little until you feel resistance, which shows the tension will hold. If you feel resistance at once, do not force it back any further. Pella warns that "the tensioning mechanism could be damaged by too much force."
- Put the cartridge back. From inside the room, hold it at the head of the window. Drive a screw into the hole in each end cap at a slight upward angle, about 25 degrees.
- Refit each guide. Set the top against the frame with the pull bar weatherstrip in the guide channel, and the bottom against the frame on top of the sill. Pella calls two things "critical." The outside edge of each guide channel must sit in the end cap. The bottom of the guide must touch the sill stop and press firmly against the jamb stops. Drive the guide screws from the bottom up.
- Test it. Push the bar down firmly with both hands, toward the ends of the bar, until it snaps into place at the sill. Then unlatch it and let it rise.
You do not have to strip the cartridge to re-tension it. In the 2017-on sheet, taking off the head cover is part of a full teardown. The winding step comes after the cartridge is put back together, and the 2016 sheet goes straight from removal to winding.
Mark the screwdriver handle with tape so each full turn is easy to count. Wind 27 turns in the direction of the arrows. Then ease back until the tensioner catches.
Now suppose you had used the 2 to 4 turns our general repair guide suggests as a start. Four turns is about 15% of the 27 Pella calls for. Spring pull rises in step with the turns wound, so the spring would have roughly a seventh of the pull it is meant to have, and the bar may still hang. On a narrow frame, 4 turns is about 36% of 11, still far short. A screen that has lost all its tension needs the full count. A small top-up is only for a spring that still pulls.
Why there is no spray lubricant on a Rolscreen
Pella prints the same caution in its service instruction, its care sheet and its owner's manual: "Operating a retractable screen may result in a static discharge. A static discharge in the presence of a flammable substance such as an aerosol lubricant could cause ignition. To avoid injury and/or property damage, do not use any flammable substance on a retractable screen."
That rules out the dry silicone spray this site suggests for other screens' tracks, in retractable screen repair for example. A silicone spray in an aerosol can is exactly the "aerosol lubricant" Pella names. None of the three Pella documents we read names any lubricant for a Rolscreen.
What Pella says to do instead is clean it. Latch the screen down. Vacuum it with the upholstery brush attachment, and use the vacuum's exhaust to blow debris off the outside of the screen if needed. For greasy marks, the owner's manual says to wash gently with hot water and mild detergent, rinse with clear water and let it dry before you let it roll up. It also says not to power-wash. Other makers' rules are in how to clean retractable and solar screens.
Where this stops applying
- Rolscreens made before February 2017. The 11 and 27 turn steps come from the sheet for units made from 2/2017 on. Pella's 2016 care sheet gives the same counts but does not say which years it covers. For an older unit, confirm with Pella (833-44-PELLA, from the owner's manual) before you wind it.
- A frame close to 20-3/4 in. Pella states the cutoff by frame width and does not say where to measure. If your window is within a fraction of an inch of it, ask Pella which count applies.
- Integrated Rolscreen and Rolscreen doors. The Integrated Rolscreen lives in the window frame and works with the sash. For Rolscreen screen doors made after 2006, the owner's manual has one line. Turn a flat-blade screwdriver in the slot at the bottom of the housing, "in the direction of the arrow." Neither is covered here.
- A spring that will not hold. If the screwdriver never meets resistance when you back off, Pella's sign that the tension will hold is missing. Stop winding and call Pella. Pella's screen warranty is described in our window warranty review. Other brands' fixes are in retractable screen repair.
- Safety. Pella's owner's manual warns that the screen "will not stop child or pet from falling out of window." A screen that rolls up properly does not change that.
Bottom line
Check that the cloth sits in both guides. If an edge is out, push it outward, raise the bar and lower it again. If the spring still pulls but runs short, top it up on the click gear a turn (8 clicks) at a time, if your cartridge has one. If it has no pull at all, take the cartridge out and wind 11 full turns (frame 20-3/4 in or less) or 27 (wider) in the direction of the arrows, then back off until it catches. Clean it with a vacuum, never an aerosol.
Sources
- Pella Corporation, Rolscreen retractable screen cartridge dis-assembly and assembly service instruction, part number 81XJ0000, rev. 10/17/2016, for Rolscreen Retractable Screen 2/2017-Current (copy hosted by All-Guides).
- Pella Corporation, Rolscreen retractable screen for windows: installation, operation and care instruction, part number 81VS0100, © 2016 (copy hosted by manualedistruzioni.it).
- Pella Corporation, Windows and patio doors owner's manual, PWPDOM0821, © 2021 (copy hosted by Lowe's).
- Pella Corporation, Pella introduces Integrated Rolscreen window innovation, press release, June 29, 2018.
Frequently asked questions
Which way do I turn a Pella Rolscreen to add tension?
In the direction of the arrows at the slotted end of the screen assembly. Pella states the direction only by those arrows, so look for them before you start.
How many turns does a Pella Rolscreen need?
From fully released, Pella's service instruction says 11 full turns for frames 20-3/4 in wide or less and 27 turns for wider frames. For a small top-up on the click gear, Pella gives no count; 8 clicks equal one turn.
Do I have to take the Rolscreen out of the window to re-tension it?
For a full re-tension, yes: the guides and the two cartridge screws come out first. The click gear top-up in Pella's 2016 care sheet needs only the head cover off, with the screen down and latched.
Can I use WD-40 or silicone spray on a Pella Rolscreen?
No. Pella warns that operating a retractable screen can cause a static discharge, and that near a flammable substance such as an aerosol lubricant it "could cause ignition." It says to use no flammable substance on the screen. Vacuum it instead.
Why does my Rolscreen go up fine but not latch at the bottom?
Pella's test is to push the bar down firmly with both hands, toward the ends of the bar, until it snaps in at the sill. If the cartridge has been out, also check that the guides went back as Pella describes: the bottom of each touching the sill stop and pressed firmly against the jamb stops.
Is the Rolscreen the same as other retractable window screens?
It works the same way, with a spring roller in a cartridge at the head, but the steps and turn counts here are Pella's own. How Pella fits among screen makers is in our retractable screen brands guide, and the screen type in general in retractable window screens.
Sources and standards consulted
- Tubular motor troubleshooting, limit-setting and remote pairing guides (manufacturer documentation)
- Lateral arm awning service manuals (pitch, arm and spring adjustment) (manufacturer documentation)
- Retractable screen manufacturer service and re-tensioning instructions (manufacturer documentation)
See how we research for our sourcing and verification process.