Can You Cut a Retractable Screen Door Kit to Fit Your Door?

Yes, if it is a box-store kit: retractable screen door kits are made to be cut, and their instructions tell you exactly how much to take off. No, if it is a custom screen: a custom unit is built to the size you order, so there is nothing left to cut. Among kits, what you may cut differs. Most let you shorten only the width, by cutting the top and bottom tracks, and you buy the height as a fixed class. The CRL kit is the exception: its cassette and pull bar are cut to the height of your jamb, 3/8 in (9.5 mm) shorter than the measurement.

Key takeaways

  • Kits fit a range uncut and are cut below it: Brisa below 32 in single or 68 in double, Andersen LuminAire below 31-7/8 in single or 68 in double.
  • Width only goes down, and on Brisa and LuminAire height is bought as a class, not cut.
  • CRL inside mount: cassette and pull bar 3/8 in (9.5 mm) under jamb height, jamb channel 1/16 in (1.6 mm) under, rails at width minus 2-1/8 in (54 mm).
  • The Brisa formula changed between editions: ODL (2014) cuts the shortfall, Larson (2019) the shortfall plus 1-7/8 in. Use the sheet in your box.

The choice between kit and custom screen is covered in retractable screen doors, and fit ranges and maximum sizes by brand in retractable screen door sizes.

Why you hear both "cut it" and "never cut it"

Both are true, for different products. A kit ships adjustable for standard doors, and its instructions include a cut step for doors narrower than its range. Larson's Brisa double sheet lists a hacksaw as an optional tool, "required if your door width is less than 68" wide."

A custom screen is the opposite. Phantom's product catalogue says its door screens "are custom made and professionally installed for all door types", and the Genius Milano 100, sold through Metro Screenworks, is ordered by width from 22 to 60 in and height from 70 to 100 in, each with a fraction box down to 1/16 in. The cutting happens at the factory, to your numbers, so there is no cut line and no allowance to remove. Reading custom-screen advice as a rule for kits, or a kit's cut step as license to trim a custom unit, is where the confusion comes from.

Cut deductions by maker

These figures are read from each maker's installation or measurement sheet: the CRL retractable screen door instructions (AVD3908, rev. 06/08), the Larson Brisa double door installation instructions (2019, document 202221006), the ODL Brisa sliding door installation instructions (2014, document 16593901), the Brisa product selection guide, and the Andersen LuminAire single and double measurement guides.

What each kit lets you cut, and by how much, as published
Kit and sheetFits uncutWhat gets cutDeductionHeight
CRL, internal mount (inside the jamb)No uncut range givenCassette with pull bar; jamb channel; both railsCassette: jamb height minus 3/8 in (9.5 mm). Channel: jamb height minus 1/16 in (1.6 mm). Rails: width minus 2-1/8 in (54 mm)Cut to fit
CRL, surface mount (on brackets)No uncut range givenCassette with pull bar; jamb channel; both railsCassette: bracket spacing minus 5/16 in (7.9 mm). Channel: length of assembled cassette. Rails: outer-edge width minus 2-1/8 inCut to fit
CRL, French door (two single kits)No uncut range givenRails only; no jamb channelEach rail: outer cassette-to-cassette width / 2, minus 1-13/16 in (46 mm)As the single kit
Larson Brisa double (2019)68 to 72 in door trim openingTop and bottom tracks, at the ends that go into the decorative housing68 in minus your opening, plus 1-7/8 in (sheet example: 66 in opening, 3-7/8 in cut)Not cut: 78, 80 or 96 in models
ODL Brisa sliding (2014)32 to 36 in, trim to center of the fixed panel's frameTop and bottom tracks, at the flat ends; "Do not cut the notch end"32 in minus your opening (sheet example: 30 in opening, 2 in cut)Not cut: one 80 in model
Brisa single (selection guide)32 to 36 in"Two simple cuts" below 32 inNot given in the guide; see the installation manualNot cut: 78, 80 or 96 in models
Andersen LuminAire single31-7/8 to 36-3/8 in"Requires Cutting" below 31-7/8 inNot given in the measurement guideNot cut: class 80 to 80-7/8 in
Andersen LuminAire double68 to 72 in"Requires Cutting" below 68 inNot given in the measurement guideNot cut: 78, 80 or 84 in classes, each 7/8 in wide

Two makers' names need a note. Brisa was sold under ODL's name in the 2014 sheet and under Larson's in the 2019 one. The Andersen guides say the LuminAire is made by Emco Enterprises, a wholly owned subsidiary of Andersen. The deductions do not transfer from one brand to another. The brands behind each product type are in our retractable screen brands guide.

The CRL kit: the one you cut to height

CRL's is the only sheet we read in which the cassette itself is cut. Tape labels on the cassette ends show which end to cut and which not to. The internal mount sequence:

  1. Mark and cut the cassette. Measure the jamb height where the cassette will sit, allowing for door stops and sill slope. Leave the temporary end cap on, measure from the bottom ("No Cut") end, and mark the cassette 3/8 in (9.5 mm) shorter than the jamb height. Hold the pull bar tight against the cassette and cut both at the same time, so they finish the same length.
  2. Clear and de-burr the tube. Stand the cassette cut end down and tap it on the floor to shake out the shavings, then de-burr the inside of the round aluminum tube the screen cloth winds on. CRL asks for an inside edge "free of any sharp edges or burrs".
  3. Fit the permanent end cap and pull bar guides, and test that the screen pulls out and retracts.
  4. Cut the jamb channel. Measure the jamb height on the opposite side and cut the channel 1/16 in (1.6 mm) short.
  5. Cut both rails at once. Measure the jamb width at top and bottom, put the top and bottom rails together with their ends flush, subtract 2-1/8 in (54 mm) and cut them together. Then crimp the weatherstrip channel at each cut end with a flat screwdriver so the strip cannot creep.

For a surface mount the bottom bracket goes as low as possible with the top bracket plumb above it, and the cassette is cut to the bracket spacing minus 5/16 in; the other cuts are in the table. For a French door CRL uses two single kits and offers one-piece 72 in (1829 mm) rails (ERS1W white, ERS1BRZ bronze) for installers who would rather not join two rail sections.

Worked example: A single door, CRL internal mount. The jamb measures 80-1/4 in (2038 mm) high on the cassette side and 80-3/16 in on the latch side, and 35-7/8 in (911 mm) wide at both top and bottom. Cassette and pull bar: 80-1/4 - 3/8 = 79-7/8 in (2029 mm), measured from the No Cut end. Jamb channel: 80-3/16 - 1/16 = 80-1/8 in. Rails: 35-7/8 - 2-1/8 = 33-3/4 in (857 mm), both cut together. Now a French door with two CRL kits, the cassettes mounted 71 in (1803 mm) apart at their outer edges: 71 / 2 = 35-1/2 in, minus 1-13/16 in, gives 33-11/16 in (856 mm) for each of the four rails.

Brisa: two sheets, two formulas

ODL's 2014 sliding door sheet takes the shortfall straight off the tracks: a 30 in opening is 2 in under the 32 in standard, and the sheet says to cut 2 in from the flat ends of the top and bottom tracks, never the notched end. Larson's 2019 double door sheet adds a fixed amount: a 66 in opening is 2 in under the 68 in standard, plus 1-7/8 in, for "3-7/8" total amount to be cut from the ends of the top and bottom tracks", the ends that go into the decorative housing. The sheet does not explain the 1-7/8 in.

Apply that to a 64 in pair of doors and the Larson arithmetic gives 68 - 64 = 4 in, plus 1-7/8 in, so 5-7/8 in (149 mm) comes off. The width Larson means is the door trim opening: Brisa is a face mount that needs a door frame or brickmold, and Larson says it cannot go on stucco without one.

Installer tip: Aluminum track can always be cut again but never lengthened. If the arithmetic leaves you unsure, leave 1/4 in (6 mm) beyond your mark, dry fit the assembly in the opening, and take off the rest.

What you cannot cut, even on a kit

Height, on most kits. Brisa and LuminAire sell height as a model, not a cut. Brisa comes in short 78 in, standard 80 in and tall 96 in versions, and the LuminAire's 80 in class covers 80 to 80-7/8 in. Between classes, the choices are a kit whose cassette is cut to height, like CRL's, or a custom screen.

Width beyond the range. No sheet we read stretches a kit past 36-3/8 in single or 72 in double; the breakpoints for what to buy instead are in retractable screen door sizes.

The mesh. None of these sheets has a step that cuts the screen cloth.

A custom screen. The Phantom and Genius figures are ordering limits, not cut ranges. Read the measuring method in how to measure for retractable screens before you order, because the order form is the only cut you get.

Retract Wise analysis: The width you cut to is not the opening width, and that is the easiest way to ruin a kit. CRL takes 2-1/8 in off the jamb width, Larson adds 1-7/8 in to the shortfall from the trim opening, and ODL measures a slider from the trim to the center of the fixed panel's frame. Cut a CRL rail to the full opening and it is 2-1/8 in too long; cut a Larson track by the shortfall alone and it is 1-7/8 in too long. Both are fixed by cutting again. Using another brand's allowance can leave a track too short, and that is a replacement part. The rule: write the maker's deduction and measuring point on the track before you pick up the saw.

How to make the cut cleanly

Larson lists a hacksaw. Cut paired parts together where the sheet says so (CRL's cassette with its pull bar, its top rail with its bottom rail, ends flush) so they finish the same length, and check which end you are cutting from: CRL labels its No Cut end, ODL says not to cut the notched end, Larson cuts the ends that go into the decorative housing. De-burr every cut end and tap out the chips, then crimp or re-seat the weatherstrip where the sheet asks, so the pile cannot walk out of its channel; the seals are covered in brush seals and pile weatherstrip. Assembly then follows how to install a retractable screen door: housing plumb first, then track, latch and spring tension.

Where this stops applying

The deductions belong to the documents named. They are from CRL revision 06/08, Larson's 2019 Brisa double sheet and ODL's 2014 Brisa sliding sheet. A newer edition can change them, as the two Brisa sheets show. The Andersen guides say where cutting starts but not how much.

No sheet we read gives a minimum width. The housings still need flat trim to fix to; Andersen asks for 3/4 in (19 mm) of flat trim face and 3/4 in of depth.

Doors in pairs and sliders are separate cases. CRL's French door rails are cut from the distance between two cassettes, not from the opening, and a slider kit covers only the vent panel. Configuration choices are in retractable screens for French doors and screens for sliding glass doors.

If no kit can be cut to your opening, the next step is a custom screen; price ranges for both are in retractable screen cost.

Frequently asked questions

Can you shorten a retractable screen door that is too tall?

Only on a kit that is designed for it. The CRL kit cuts the cassette and pull bar to 3/8 in (9.5 mm) under the jamb height for an inside mount. Brisa and Andersen LuminAire kits are bought by height class (78, 80, 84 or 96 in depending on the kit) and their height is not cut.

How much do you cut off a Brisa retractable screen door?

It depends on the sheet in the box. Larson's 2019 double sheet: 68 in minus your door trim opening, plus 1-7/8 in, from the ends of the top and bottom tracks. ODL's 2014 sliding sheet: 32 in minus your opening, from the flat ends only. From 68 to 72 in (double) or 32 to 36 in (single and sliding), nothing is cut.

Sources and standards consulted

  • International Residential Code (IRC), wood framing and fastening provisions (ICC)
  • NFPA 70, National Electrical Code (outdoor receptacles, GFCI and wet location requirements) (NFPA)
  • Anchor manufacturer technical guides for masonry and concrete fastening (edge distance, embedment) (manufacturer documentation)
  • Manufacturer installation manuals for awnings, retractable screen doors and motorized screens (manufacturer documentation)

See how we research for our sourcing and verification process.